- 您現在的位置：買賣IC網 > PDF目錄377770 > LTC2480IDD (LINEAR TECHNOLOGY CORP) 16-Bit ADC with Easy Drive PDF資料下載
參數資料
| 型號： | LTC2480IDD |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 16-Bit ADC with Easy Drive |
| 中文描述： | 1-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO10 |
| 封裝： | 3 X 3 MM, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件頁數： | 20/40頁 |
| 文件大小： | 535K |
| 代理商： | LTC2480IDD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
20
LTC2480
2480f
temperature dependent offset error due to the input
leakage current. A 1nA input leakage current will develop
a 1ppm offset error on a 5k resistor if V
REF
= 5V. This error
has a very strong temperature dependency.
SERIAL INTERFACE TIMING MODES
The LTC2480’s 4-wire interface is SPI and MICROWIRE
compatible. This interface offers several flexible modes of
operation. These include internal/external serial clock,
3- or 4-wire I/O, single cycle or continuous conversion.
The following sections describe each of these serial inter-
face timing modes in detail. In all these cases, the con-
verter can use the internal oscillator (F
O
= LOW or F
O
=
HIGH) or an external oscillator connected to the F
O
pin.
Refer to Table 6 for a summary.
External Serial Clock, Single Cycle Operation
(SPI/MICROWIRE Compatible)
This timing mode uses an external serial clock to shift out
the conversion result and a CS signal to monitor and
control the state of the conversion cycle, see Figure 5.
The serial clock mode is selected on the falling edge of CS.
To select the external serial clock mode, the serial clock pin
(SCK) must be LOW during each CS falling edge.
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may be
pulled LOW in order to monitor the state of the converter.
While CS is pulled LOW, EOC is output to the SDO pin.
EOC = 1 while a conversion is in progress and EOC = 0 if
the device is in the sleep state. Independent of CS, the
device automatically enters the low power sleep state once
the conversion is complete.
When the device is in the sleep state, its conversion result
is held in an internal static shift register. The device
remains in the sleep state until the first rising edge of SCK
is seen while CS is LOW. The input data is then shifted in
via the SDI pin on the rising edge of SCK (including the
first rising edge) and the output data is shifted out of the
SDO pin on each falling edge of SCK
. This enables
external circuitry to latch the output on the rising edge of
SCK. EOC can be latched on the first rising edge of SCK
and the last bit of the conversion result can be latched on
the 24th rising edge of SCK. On the 24th falling edge of
SCK, the device begins a new conversion. SDO goes HIGH
(EOC = 1) indicating a conversion is in progress.
In
applications where the processor generates 32 clock
cycles, or to remain compatible with higher resolution
converters, the LTC2480’s digital interface will ignore
extra clock edges seen during the next conversion period
after the 24th and outputs “1” for the extra clock cycles.
At the conclusion of the data cycle, CS may remain LOW
and EOC monitored as an end-of-conversion interrupt.
Alternatively, CS may be driven HIGH setting SDO to Hi-Z.
As described above, CS may be pulled LOW at any time in
order to monitor the conversion status.
Typically, CS remains LOW during the data output state.
However, the data output state may be aborted by pulling
CS HIGH anytime between the first rising edge and the 24th
falling edge of SCK (see Figure 6). On the rising edge of CS,
the device aborts the data output state and immediately
initiates a new conversion. If the device has not finished
loading the last input bit SPD of SDI by the time CS is pulled
HIGH, the SDI information is discarded and the previous
configuration is kept. This is useful for systems not requir-
ing all 24 bits of output data, aborting an invalid conversion
cycle or synchronizing the start of a conversion.
APPLICATIU
W
U
U
Table 6. LTC2480 Interface Timing Modes
CONVERSION
CYCLE
CONTROL
CS and SCK
SCK
CS
↓
Continuous
DATA
OUTPUT
CONTROL
CS and SCK
SCK
CS
↓
Internal
CONNECTION
and
WAVEFORMS
Figures 5, 6
Figure 7
Figures 8, 9
Figure 10
SCK
CONFIGURATION
External SCK, Single Cycle Conversion
External SCK, 3-Wire I/O
Internal SCK, Single Cycle Conversion
Internal SCK, 3-Wire I/O, Continuous Conversion
SOURCE
External
External
Internal
Internal
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2480CDD | 16-Bit ADC with Easy Drive |
| LTC2486 | 16-Bit 2-/4-Channel ツヒ ADC with PGA and Easy Drive Input Current Cancellation |
| LTC2486CDE | 16-Bit 2-/4-Channel ツヒ ADC with PGA and Easy Drive Input Current Cancellation |
| LTC2486IDE | 16-Bit 2-/4-Channel ツヒ ADC with PGA and Easy Drive Input Current Cancellation |
| LTC2487 | 16-Bit 2-/4-Channel ADC with PGA, Easy Drive and I2C Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2480IDD#PBF | 功能描述:IC ADC 16BIT 10-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2480IDD#TR | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 7.5sps 16-bit Serial 10-Pin DFN EP T/R |
| LTC2480IDD#TRPBF | 功能描述:IC ADC 16BIT 10-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2480IMS#PBF | 功能描述:IC ADC 16BIT 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2480IMS#TRPBF | 功能描述:IC ADC 16BIT 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。