- 您現在的位置：買賣IC網 > PDF目錄2006 > LTC2498IUHF#TRPBF (Linear Technology)IC ADC 24BIT 16CH 38-QFN PDF資料下載
參數資料
| 型號： | LTC2498IUHF#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 20/38頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT 16CH 38-QFN |
| 標準包裝： | 2,500 |
| 位數： | 24 |
| 采樣率（每秒）： | 7.5 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 38-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 38-QFN（5x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 16 個單端，雙極；8 個差分，雙極 |
| 配用： | DC1011A-A-ND - BOARD DELTA SIGMA ADC LTC2498 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
LTC2498
27
2498ff
The input data is shifted through the SDI pin on the ris-
ing edge of SCK (including the first rising edge) and the
output data is shifted out the SDO pin on the falling edge
of SCK. The data input/output cycle is concluded and a
new conversion automatically begins after the 32nd rising
edge of SCK. During the next conversion, SCK and SDO
remain HIGH until the conversion is complete.
The Use of a 10k Pull-Up on SCK for Internal SCK
Selection
If CS is pulled HIGH while the converter is driving SCK
LOW, the internal pull-up is not available to restore SCK
to a logic HIGH state if SCK is floating. This will cause the
device to exit the internal SCK mode on the next falling
edge of CS. This can be avoided by adding an external 10k
pull-up resistor to the SCK pin.
Whenever SCK is LOW, the LTC2498’s internal pull-up at
SCK is disabled. Normally, SCK is not externally driven if
the device is operating in the internal SCK timing mode.
However, certain applications may require an external
driver on SCK. If the driver goes Hi-Z after outputting a
LOW signal, the internal pull-up is disabled. An external
10k pull-up resistor prevents the device from exiting the
internal SCK mode under this condition.
AsimilarsituationmayoccurduringthesleepstatewhenCS
is pulsed HIGH-LOW-HIGH in order to test the conversion
status. If the device is in the sleep state (EOC = 0), SCK
will go LOW. If CS goes HIGH before the time tEOCTEST,
the internal pull-up is activated. If SCK is heavily loaded,
the internal pull-up may not restore SCK to a HIGH state
before the next falling edge of CS. The external 10k pull-up
resistor prevents the device from exiting the internal SCK
mode under this condition.
PRESERVING THE CONVERTER ACCURACY
The LTC2498 is designed to reduce as much as possible
sensitivity to device decoupling, PCB layout, anti-aliasing
circuits, line frequency perturbations, and temperature
sensitivity. In order to achieve maximum performance a
few simple precautions should be observed.
Digital Signal Levels
The LTC2498’s digital interface is easy to use. Its digital
inputs (SDI, fO, CS, and SCK in external serial clock mode)
accept standard CMOS logic levels. Internal hysteresis
circuitscantolerateedgetransitiontimesasslowas100s.
The digital input signal range is 0.5V to VCC – 0.5V. During
transitions, the CMOS input circuits draw dynamic cur-
rent. For optimal performance, application of signals to
the serial data interface should be reserved for the sleep
and data output periods.
During the conversion period, overshoot and undershoot
of fast digital signals applied to both the serial digital
interface and the external oscillator pin (fO) may degrade
the converter performance. Undershoot and overshoot
occur due to impedance mismatch of the circuit board
trace at the converter pin when the transition time of an
external control signal is less than twice the propagation
delay from the driver to the input pin. For reference, on a
regularFR-4board,thepropagationdelayisapproximately
183ps/inch. In order to prevent overshoot, a driver with
a 1ns transition time must be connected to the converter
through a trace shorter than 2.5 inches. This becomes
difficult when shared control lines are used and multiple
reflections occur.
Parallel termination near the input pin of the LTC2498 will
eliminate this problem, but will increase the driver power
dissipation. A series resistor from 27 to 54 (depend-
ing on the trace impedance and connection) placed near
the driver will also eliminate over/undershoot without
additional driver power dissipation.
For many applications, the serial interface pins (SCK, SDI,
CS, fO) remain static during the conversion cycle and no
degradation occurs. On the other hand, if an external
oscillator is used (fO driven externally) it is active during
the conversion cycle. Moreover, the digital filter rejection
is minimal at the clock rate applied to fO. Care must be
taken to ensure external inputs and reference lines do not
cross this signal or run near it. These issues are avoided
when using the internal oscillator.
applications inForMation
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2600IUFD#PBF | IC DAC OCTAL R-R 16BIT 20-QFN |
| LTC2602IMS8#TRPBF | IC DAC 16BIT DUAL R-R VOUT 8MSOP |
| LTC2604IGN-1#TRPBF | IC DAC 16BIT QUAD R-R OUT 16SSOP |
| LTC2605IGN-1#TRPBF | IC DAC 16BIT OCT I2C 16-SSOP |
| LTC2606IDD#TRPBF | IC DAC 16BIT I2C V-OUT 10-DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2499CUHF | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 7.5sps 24-bit Serial 38-Pin QFN EP |
| LTC2499CUHF#PBF | 功能描述:IC ADC 24BIT DELTA SIG 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2499CUHF#TRPBF | 功能描述:IC ADC 24BIT DELTA SIG 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2499CUHFPBF | 制造商:Linear Technology 功能描述:24bit Delta Sigma ADC Temp Sens LTC2499 |
| LTC2499IUHF#PBF | 功能描述:IC ADC 24BIT DELTA SIG 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。