- 您現在的位置：買賣IC網 > PDF目錄377777 > LTC3711 (Linear Technology Corporation) 4A, High Efficiency, Standalone Li Battery Charger PDF資料下載
參數資料
| 型號： | LTC3711 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 4A, High Efficiency, Standalone Li Battery Charger |
| 中文描述： | 第4A，高效，獨立鋰電池充電器 |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 241K |
| 代理商： | LTC3711 |
10
LTC4007
4007i
The peak inductor current, at which I
CMP
resets the SR
latch, is controlled by the voltage on ITH. ITH is in turn
controlled by several loops, depending upon the situation
at hand. The average current control loop converts the
voltage between CSP and BAT to a representative current.
Error amp CA2 compares this current against the desired
current programmed by R
PROG
at the PROG pin and
adjusts ITH until:
V
R
k
PROG
3
therefore,
V
R
PROG
V
V
A
k
REF
CSP
BAT
=
+
μ
–
.
11 67
3
I
A
k
R
CHARGE MAX
REF
SENSE
(
)
–
.
=
μ
11 67
3
The voltage at BAT is divided down by an internal resistor
divider and is used by error amp EA to decrease ITH if the
divider voltage is above the 1.19V reference. When the
charging current begins to decrease, the voltage at PROG
will decrease in direct proportion. The voltage at PROG is
then given by:
V
I
R
A
k
R
k
PROG
CHARGE
SENSE
PROG
3
=
+
μ
(
)
.
11 67
3
V
PROG
is plotted in Figure 2.
The amplifier CL1 monitors and limits the input current,
normally from the AC adapter to a preset level (100mV/
R
CL
). At input current limit, CL1 will decrease the ITH
OPERATIOU
I
CHARGE
(% OF MAXIMUM CURRENT)
0
0
V
P
0.2
0.4
0.6
0.8
20
40
60
80
100
4007 F02
1.0
1.2
1.19V
0.309V
Figure 2. V
PROG
vs I
CHARGE
voltage, thereby reducing charging current. The I
CL
indica-
tor output will go low when this condition is detected and
the FLAG indicator will be inhibited if it is not already LOW.
If the charging current decreases below 10% to 15% of
programmed current while engaged in input current lim-
iting, BGATE will be forced low to prevent the charger from
discharging the battery. Audible noise can occur in this
mode of operation.
An overvoltage comparator guards against voltage tran-
sient overshoots (>7% of programmed value). In this
case, both MOSFETs are turned off until the overvoltage
condition is cleared. This feature is useful for batteries
which “l(fā)oad dump” themselves by opening their protec-
tion switch to perform functions such as calibration or
pulse mode charging.
PWM Watchdog Timer
There is a watchdog timer that observes the activity on the
BGATE and TGATE pins. If TGATE stops switching for
more than 40
μ
s, the watchdog activates and turns off the
top MOSFET for about 400ns. The watchdog engages to
prevent very low frequency operation in dropout—a po-
tential source of audible noise when using ceramic input
and output capacitors.
Charger Start-Up
When the charger is enabled, it will not begin switching
until the ITH voltage exceeds a threshold that assures
initial current will be positive. This threshold is 5% to 15%
of the maximum programmed current. After the charger
begins switching, the various loops will control the current
at a level that is higher or lower than the initial current. The
duration of this transient condition depends upon the loop
compensation, but is typically less than 100
μ
s.
Thermistor Detection
The thermistor detection circuit is shown in Figure 3. It
requires an external resistor and capacitor in order to
function properly.
The thermistor detector performs a sample-and-hold func-
tion. An internal clock, whose frequency is determined by
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4008 | 4A, High Efficiency, Standalone Li Battery Charger |
| LTC4010 | High Efficiency Standalone Nickel Battery Charger |
| LTC4010EFE | High Efficiency Standalone Nickel Battery Charger |
| LTC4052-42 | Lithium-Ion Battery Pulse Charger with Overcurrent Protection |
| LTC4052EMS8E-4.2 | Lithium-Ion Battery Pulse Charger with Overcurrent Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3711EGN | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3711EGN#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3711EGN#TR | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3711EGN#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3713EG | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。