- 您現在的位置：買賣IC網 > PDF目錄69008 > LTC4269CDKD-2 (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 PDF資料下載
參數資料
| 型號： | LTC4269CDKD-2 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 |
| 封裝： | 7 X 4 MM, PLASTIC, M0-229, DFN-32 |
| 文件頁數： | 2/34頁 |
| 文件大?。?/td> | 383K |
| 代理商： | LTC4269CDKD-2 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
LTC4269-2
0
42692fb
pin FuncTions
SHDN (Pin 1): Shutdown Input. Use this pin for auxiliary
power application. Drive SHDN high to disable LTC4269-2
operation and corrupt the signature resistance. If unused,
tie SHDN to VPORTN.
T2P (Pin 2): Type-2 PSE Indicator, Open-Drain. Low
impedance indicates the presence of a Type-2 PSE.
RCLASS (Pin 3): Class Select Input. Connect a resistor
between RCLASS and VPORTN to set the classification load
current.
VPORTN(Pins5,6):PowerInput.TietothePDinputthrough
the diode bridge. Pins 5 and 6 must be electrically tied
together at the package.
NC (Pins 4, 7, 8, 25, 30, 31): No Connect.
COMP (Pin 9): Output Pin of the Error Amplifier. The error
amplifier is an op amp, allowing various compensation
networks to be connected between the COMP pin and
FB pin for optimum transient response in a nonisolated
supply. The voltage on this pin corresponds to the peak
current of the external FET. Full operating voltage range is
between 0.8V and 2.5V corresponding to 0mV to 220mV
at the ISENSE pin. For applications using the 100mV OC
pin for overcurrent detection, typical operating range for
the COMP pin is 0.8V to 1.6V. For isolated applications
where COMP is controlled by an opto-coupler, the COMP
pin output drive can be disabled with FB = VREF, reducing
the COMP pin current to (COMP – 0.7)/40k.
FB(Pin10):Inanonisolatedsupply,FBmonitorstheoutput
voltage via an external resistor divider and is compared
with an internal 1.23V reference by the error amplifier. FB
connected to VREF disables error amplifier output.
ROSC (Pin11): A resistor to GND programs the operating
frequency of the IC between 100kHz and 500kHz. Nominal
voltage on the ROSC pin is 1.0V.
SYNC (Pin 12): Used to synchronize the internal oscillator
to an external signal. It is directly logic compatible and
can be driven with any signal between 10% and 90% duty
cycle. If unused, the pin should be connected to GND.
SS_MAXDC (Pin 13): The external resistor divider from
VREF sets the maximum duty cycle clamp (SS_MAXDC =
1.84V, SD_VSEC = 1.32V gives 72% duty cycle). Capacitor
on SS_MAXDC pin in combination with external resistor
divider sets soft-start timing.
VREF (Pin 14): The output of an internal 2.5V reference
which supplies internal control circuitry. Capable of sourc-
ing up to 2.5mA drive for external use. Bypass to GND
with a 0.1F ceramic capacitor.
SD_VSEC (Pin 15): The SD_VSEC pin, when pulled below
its accurate 1.32V threshold, is used to turn off the IC and
reduce current drain from VIN. The SD_VSEC pin is con-
nectedtosysteminputvoltagethrougharesistordividerto
define undervoltage lockout (UVLO) for the power supply
and to provide a volt-second clamp on the OUT pin. An
11A pin current hysteresis allows external programming
of UVLO hysteresis.
GND (Pin 16): Analog Ground. Tie to VNEG.
BLANK (Pin 17): A resistor to GND adjusts the extended
blanking period of the overcurrent and current sense
amplifier outputs during FET turn-on—to prevent false
current limit trip. Increasing the resistor value increases
the blanking period.
ISENSE (Pin 18): The Current Sense Input for the Control
Loop. Connect this pin to the sense resistor in the source
of the external power MOSFET. A resistor in series with
the ISENSE pin programs slope compensation.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4269IDKD-2#TR | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 |
| LTC4412IS6#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC4412IS6#TRM | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC4558EUD#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| LTC4558EUD | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4269CDKD-2#PBF | 功能描述:IC PD/SYNC FORWARD CTRLR 32-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4269CDKD-2#TRPBF | 功能描述:IC PD/SYNC FORWARD CTRLR 32-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC4269CDKD-2-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at High Power PD and Synchronous Forward Controller with AUX Support |
| LTC4269CDKD-2-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at High Power PD and Synchronous Forward Controller with AUX Support |
| LTC4269CDKD-2-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at High Power PD and Synchronous Forward Controller with AUX Support |
發布緊急采購，3分鐘左右您將得到回復。