- 您現在的位置：買賣IC網 > PDF目錄367613 > LUCL7585FP-DT Full-Feature,Low-Power SLIC and Switch PDF資料下載
參數資料
| 型號： | LUCL7585FP-DT |
| 英文描述： | Full-Feature,Low-Power SLIC and Switch |
| 中文描述： | 全功能，低功耗SLIC和開關 |
| 文件頁數： | 10/22頁 |
| 文件大小： | 446K |
| 代理商： | LUCL7585FP-DT |
10
Agere Communications Inc.
Data Sheet
September 2001
L7585G Full-Feature, Low-Power SLIC and Switch
Electrical Characteristics
In general, minimum and maximum values are testing requirements. However, some parameters may not be
tested in production because they are guaranteed by design and device characterization. Typical values reflect the
design center or nominal value of the parameter; they are for information only and are not a requirement. Minimum
and maximum values apply across the entire temperature range (–40 °C to +85 °C) and entire battery range
(–35 V to –60 V). Unless otherwise specified, typical is defined as 25 °C, V
CCA
= +5.0 V, V
CCD
= +5.0 V,
V
SP
= +10 V, V
BAT
= –48 V. Positive currents flow into the device.
* Not to exceed 26 grams of water per kilogram of dry air.
This parameter is not tested in production; it is guaranteed by design and device characterization.
1. The ringing source may be either of the following:
a) The ringing source consists of the ac and dc voltages added together (battery-backed ringing); the ringing return is ground. In this case,
bit B3 will always be a 1 when ringing is applied.
b) The ringing source consists of only the ac voltage (earth-backed ringing); the ringing return is the dc voltage. In this case, bit B3 will
always be a 0 when ringing is applied.
2. NDET must also indicate ring trip when the ac ringing voltage is absent (<5 Vrms) from the ringing source.
3. Pretrip ringing must not be tripped by a 10 k
resistor in parallel with an 8 μF capacitor applied across tip and ring.
Table 4. Operating Conditions and Powering
Parameter
Min
–40
5
Typ
—
—
Max
85
95*
Unit
°C
%RH
Temperature Range
Humidity Range
Supply Voltages:
V
CCA
V
CCD
V
SP
V
BAT
V
CCA
—V
CCD
D
GND
—A
GND
Supply Currents (all states, no loop current):
I
CCA
+ I
CCD
(+5 V)
IV
SP
(+10 V)
I
BAT
(–48 V)
Total Power Dissipation (all states, no loop current)
(V
CC
= +5 V; V
SP
= +10 V; V
BAT
= –48 V)
Power Supply Rejection (tip/ring and transmit)
:
V
CCA
(500 Hz—3 kHz; 50 mVrms ripple)
V
CCD
(500 Hz—3 kHz; 50 mVrms ripple)
V
SP
(500 Hz—3 kHz; 250 mVrms ripple)
V
BAT
(500 Hz—3 kHz; 50 mVrms ripple)
Thermal
:
Thermal Resistance (still air)
Operating T
JC
4.75
4.75
8.0
–35
—
—
5.0
5.0
10
–48
—
—
5.5
5.5
12.0
–60
±0.5
±0.25
V
V
V
V
V
V
—
—
—
—
4.9
45
–3.1
175
7.0
200
–4.0
200
mA
μA
mA
mW
30
45
45
45
40
—
—
—
—
—
—
—
dB
dB
dB
dB
—
—
—
—
47
155
°C/W
°C
Table 5. Ring Trip Detector
Parameter
Min
±2.5
±12
Typ
±3
±15
Max
±3.5
±18
Unit
V
V
Voltage at input that will cause ring trip after appropriate zero crossings.
Voltage at input that will cause immediate ring trip.
Ringing Source
1
:
Frequency (f)
dc Voltage
ac Voltage
Ring Trip (NDET = 0)
2, 3
:
Loop Resistance
Trip Time
NDET Valid
19
–39.5
60
20
—
—
28
–57
105
Hz
V
Vrms
2000
—
—
—
—
—
—
200
80
ms
ms
相關PDF資料 |
PDF描述 |
|---|---|
| LUCL7590CAE-D | Telephone Ringing Driver |
| LUCL7590CAE-DT | Telephone Ringing Driver |
| LUCL8560EP-DT | Low-Power SLIC with Ringing |
| LUCL8560GP-D | Low-Power SLIC with Ringing |
| LUCL8560GP-DT | Low-Power SLIC with Ringing |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LUCL7585GBE-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Full-Feature,Low-Power SLIC and Switch |
| LUCL7585GBE-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Full-Feature,Low-Power SLIC and Switch |
| LUCL7590BAE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telephone Ringer |
| LUCL7590CAE-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Telephone Ringing Driver |
| LUCL7590CAE-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Telephone Ringing Driver |
發布緊急采購，3分鐘左右您將得到回復。