- 您現在的位置：買賣IC網 > PDF目錄367613 > LUCL8567AP-DT SLIC for Peoples Republic of China Applications PDF資料下載
參數資料
| 型號： | LUCL8567AP-DT |
| 英文描述： | SLIC for Peoples Republic of China Applications |
| 中文描述： | 為人民共和國的中國用戶接口的應用 |
| 文件頁數： | 38/42頁 |
| 文件大小： | 701K |
| 代理商： | LUCL8567AP-DT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁
38
Lucent Technologies Inc.
Data Sheet
August 1999
People’s Republic of China Applications
L8567 SLIC for
dc Applications
(continued)
Latched Parallel Data Interface
(continued)
Table 24. Valid Data at NSTAT and NTSD
A simplified logic output latches schematic is shown in
Figure 30.
12-3455(F)
Figure 30. Logic Output Latches
Like NSTAT, output NLED also reflects loop closure and
ring trip status. Output NLED is not latched. This output
is an open-collector output with sufficient drive capabil-
ity to drive an LED. Multiple NLED can be connected to
a common LED. NLED is valid regardless of the state
of EN. NLED can be used as an unlatched alternative
to NSTAT for control logic.
ac Design
There are four key ac design parameters.
Termination
impedance
is the impedance looking into the 2-wire
port of the line card. It is set to match the impedance of
the telephone loop in order to minimize echo return to
the telephone set.
Transmit gain
is measured from the
2-wire port to the PCM highway, while
receive gain
is
done from the PCM highway to the transmit port.
Finally, the
hybrid balance
network cancels the
unwanted amount of the receive signal that appears at
the transmit port.
First-Generation Codecs
These perform the basic filtering, A/D (transmit), D/A
(receive), and μ-law/A-law companding. They all have
an op amp in front of the A/D converter for transmit
gain setting and hybrid balance (cancellation at the
summing node). Depending on the type, some have
differential analog input stages, differential analog out-
put stages, and μ-law/A-law selectability. This genera-
tion of codecs is lower cost compared to second- and
third-generation codecs, but needs the most compli-
cated interface between the SLIC and codec. These
codecs are most suitable for applications with fixed
gains, termination impedance, and hybrid balance.
Second-Generation Codecs
This class of devices includes a microprocessor inter-
face for software control of the gains and hybrid bal-
ance. The hybrid balance is included in the device. ac
programmability adds application flexibility and saves
several passive components and also adds several I/O
latches that are needed in the application. However,
there is no transmit op amp, since the transmit gain and
hybrid balance are set internally.
Third-Generation Codecs
This class of devices includes the gains, termination
impedance, and hybrid balance—all under micropro-
cessor control. Depending on the device, it may or may
not include latches. This generation of codec offers a
very simple SLIC-codec interface with a minimal num-
ber of external components.
T7507 Codec
The T7507 provides third-generation codec functional-
ity without the programmability. In the T7507, ac gain,
termination impedance, and the hybrid balance net-
work are set digitally; thus, the SLIC-codec interface
requires virtually no external components.
However, because all the ac parameters are fixed (and
set for requirements in the PRC), the device is an
extremely cost-effective solution.
EN
0
0
1
EN
0
0
State
NSTAT
0
1
1
NTSD
0
1
Off-hook—loop closure or ring trip
On-hook
Don’t care
State
Device in thermal shutdown
Normal operation—device state deter-
mined by B0, B1, and RD1 inputs
Don’t care
1
1
NRDET
NLC
NSTAT
EN
CONTROL
INTERNAL
LOOP
CLOSURE
DETECTORS
相關PDF資料 |
PDF描述 |
|---|---|
| LUCL8567AAU-D | GT 48C 48#16 SKT RECP |
| LUCL8567AAU-DT | Circular Connector; MIL SPEC:MIL-C-5015; Body Material:Metal; Series:GT; No. of Contacts:4; Connector Shell Size:36; Connecting Termination:Solder; Circular Shell Style:Square Flange Receptacle; Body Style:Straight |
| LUCL8574DP-D | L8574D Resistive Subscriber Line Interface Circuit(SLIC), Ring Relay,and Protector(SRP)for Long Loop and TR-57 Applications |
| LUCL8574DP-DT | L8574D Resistive Subscriber Line Interface Circuit(SLIC), Ring Relay,and Protector(SRP)for Long Loop and TR-57 Applications |
| LUCL8575BP | Dual-Resistive,Low-Cost Subscriber Line Interface Circuit(SLIC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LUCL8574CP-D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Subscriber Line Interface Circuit |
| LUCL8574DP-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:L8574D Resistive Subscriber Line Interface Circuit(SLIC), Ring Relay,and Protector(SRP)for Long Loop and TR-57 Applications |
| LUCL8574DP-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:L8574D Resistive Subscriber Line Interface Circuit(SLIC), Ring Relay,and Protector(SRP)for Long Loop and TR-57 Applications |
| LUCL8575BP | 制造商:AGERE 制造商全稱:AGERE 功能描述:Dual-Resistive,Low-Cost Subscriber Line Interface Circuit(SLIC) |
| LUCL8575BP-TR | 制造商:AGERE 制造商全稱:AGERE 功能描述:Dual-Resistive,Low-Cost Subscriber Line Interface Circuit(SLIC) |
發布緊急采購，3分鐘左右您將得到回復。