- 您現在的位置：買賣IC網 > PDF目錄367613 > LUCL9215GRG-D Short-Loop Sine Wave Ringing SLIC PDF資料下載
參數資料
| 型號： | LUCL9215GRG-D |
| 英文描述： | Short-Loop Sine Wave Ringing SLIC |
| 中文描述： | 短回路正弦波振鈴用戶接口 |
| 文件頁數： | 29/50頁 |
| 文件大?。?/td> | 1115K |
| 代理商： | LUCL9215GRG-D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
Data Sheet
September 2001
Short-Loop Sine Wave Ringing SLIC
L9215A/G
Agere Systems Inc.
29
Supervision
(continued)
Power Ring
(continued)
Sine Wave Input Signal and Sine Wave Power Ring Signal Output
(continued)
It is recommended that the input level at RING
IN
be adjusted so that the power ring signal at tip and ring is just at
the edge or slightly clipping. This gives maximum power transfer with minimal distortion of the sine wave. The tip
side will saturate at a nominal 1 V above ground. The ring side will saturate at a nominal 3 V above battery. The
input circuit for a sine wave along with waveforms to illustrate the tip and ring saturation is shown in Figure 12.
12-3532.H(F)
Figure 12. RING
IN
Operation
The point at which clipping of the power ring signal begins at tip and ring is a function of the battery voltage, the
input capacitor at RING
IN
, and the input signal at RING
IN
and Vcc. Typical characteristic conditions showing the
onset of clipping are given below.
Table 21. Onset of Power Ringing Clipping V
CC
= 5 V, Cinput = 0.47
μ
F
Table 22. Onset of Power Ringing Clipping V
CC
= 3.1 V, Cinput = 0.47
μ
F
Input
T/R
V
BAT1
(V)
–70.15
–68.06
–66.00
–64.08
–62.04
–60.05
Vrms (mV)
891
858
833
814
789
747
Vrms (V)
46.88
45.11
43.69
42.57
41.21
39.11
Gain
52.62
52.58
52.45
52.30
52.23
52.36
Input
T/R
V
BAT1
(V)
–70.12
–68.07
–66.06
–64.01
–62.00
–60.00
Vrms (mV)
894
855
824
799
780
749
Vrms (V)
47.15
45.11
43.38
41.95
40.79
39.09
Gain
52.74
52.76
52.65
52.5
52.29
52.19
GND
V
BAT
PT
+1
TR
27.5x
RING
IN
0.47
μ
F
INPUT
L9215
V
TIP
V
RING
–1
3 V
100 k
1 V
V
BAT
= –75 V
71 V
相關PDF資料 |
PDF描述 |
|---|---|
| LUCL9215GAU-D | Short-Loop Sine Wave Ringing SLIC |
| LUCL9215ARG-D | Short-Loop Sine Wave Ringing SLIC |
| LUCL9215AAU-D | GT 3C 3#0 PIN RECP WALL RM |
| LUCL9215AAU-DT | GT 14C 12# 2#16 PIN RECP WALL |
| LUCL9216GGF-D | Short-Loop Ringing SLIC with Ground Start |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LUCL9216AGF-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Ringing SLIC with Ground Start |
| LUCL9216AGF-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Ringing SLIC with Ground Start |
| LUCL9216ARG-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Ringing SLIC with Ground Start |
| LUCL9216GGF-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Ringing SLIC with Ground Start |
| LUCL9216GGF-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Ringing SLIC with Ground Start |
發布緊急采購，3分鐘左右您將得到回復。