- 您現在的位置：買賣IC網 > PDF目錄367614 > LUCL9218GAR-D CAT5E PATCH CABLES SNAGLESS,BLUE 50 FT PDF資料下載
參數資料
| 型號： | LUCL9218GAR-D |
| 英文描述： | CAT5E PATCH CABLES SNAGLESS,BLUE 50 FT |
| 中文描述： | 低成本線接口 |
| 文件頁數： | 23/30頁 |
| 文件大?。?/td> | 378K |
| 代理商： | LUCL9218GAR-D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Agere Systems Inc.
23
Data Sheet
November 2001
L9218A/G Low-Cost Line Interface
Applications
(continued)
ac Design
(continued)
Receive Interface
(continued)
With a third-generation codec, the line card designer
has different concerns. To design the ac interface, the
designer must first decide upon all termination imped-
ance, hybrid balances, and transmission-level points
(TLP) requirements that the line card must meet. In the
transmit direction, the only concern is that the SLIC
does not provide a signal that is too hot and overloads
the codec input. Thus, for the highest TLP that is being
designed to, given the SLIC gain, the designer, as a
function of voice band frequency, must ensure that the
codec is not overloaded. With a given TLP and a given
SLIC gain (if the signal will cause a codec overload),
the designer must insert some sort of loss, typically a
resistor divider, between the SLIC output and codec
input.
In the receive direction, the issue is to optimize S/N.
Again, the designer must consider all the considered
TLPs. The idea is, for all desired TLPs, to run the
codec at or as close as possible to its maximum output
signal, to optimize the S/N. Remember noise floor is
constant, so the hotter the signal from the codec, the
better the S/N. The problem is, if the codec is feeding a
high-gain SLIC, either an external resistor divider is
needed to knock the gain down to meet the TLP
requirements, or the codec is not operating near maxi-
mum signal levels, thus compromising the S/N.
It appears the solution is to have a SLIC with a low
gain, especially in the receive direction. This will allow
the codec to operate near its maximum output signal
(to optimize S/N), without an external resistor divider
(to minimize cost).
Note also that some third-generation codecs require
the designer to provide an inherent resistive termina-
tion via external networks. The codec will then provide
gain shaping, as a function of frequency to meet the
return loss requirements. Further stability issues may
add external components or excessive ground plane
requirements to the design.
To meet the unique requirements of both types of
codecs, the L9218 offers two receive gain choices.
These receive gains are mask-programmable at the
factory and are offered as two different code variations.
For interface with a first-generation codec, the L9218A
is offered with a receive gain of 7.86. For interface with
a third-generation codec, the L9218G is offered with a
receive gain of 2. In either case, the transconductance
in the transmit direction, or the transmit gain is 403
.
Example 1: Real Termination (First-Generation Codec)
ac equivalent circuits for real termination using a T7504 codec is shown in Figure 15.
Figure 16. ac Equivalent Circuit
R
P
Z
T
+
–
R
P
V
T/R
I
T/R
V
S
Z
T/R
+
–
RING
A
V
= –1
A
V
= 1
VITR
–
+
+
–
CURRENT
SENSE
TIP
+
–
R
T1
R
RCV
R
HB1
R
T2
RCVN
RCVP
R
X
VGSX
VF
X
IN
VFR
1/4 T7504 CODEC
R
G
2.4 V
–0.403 V/mA
A
V
=
3.93
L9218 SLIC
VF
X
IP
12-3581 (F).d
相關PDF資料 |
PDF描述 |
|---|---|
| LUCL9218GAR-DT | CAT5E PATCH CABLES SNAGLESS,BLUE 100 FT |
| LUCL9310GP-D | Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device |
| LUCL9310GP-DT | Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device |
| LUCL9310AP-D | Top Entry Connector Hood; Enclosure Material:Aluminum Alloy; For Use With:C146 Rectangular Circular Connectors; Thread Size:PG 21; Connecting Termination:Screw; Gender:Male; No. of Contacts:16; Operating Voltage:400V; Series:C-146 RoHS Compliant: Yes |
| LUCL9310AP-DT | Side Entry Connector Hood; Enclosure Material:Aluminum Alloy; For Use With:C146 Rectangular Circular Connectors; Thread Size:PG 21; Connecting Termination:Screw; Gender:Male; No. of Contacts:24; Operating Voltage:400V; Series:C-146 RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LUCL9218GAR-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface |
| LUCL9219AAR-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit |
| LUCL9219AAR-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit |
| LUCL9219GAR-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit |
| LUCL9219GAR-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit |
發布緊急采購，3分鐘左右您將得到回復。