Revision 13 1-7 Pro I/Os with Advanced I/O Standards The IGLOOe family of FPGAs features a flexible I/O struct" />
參數資料
型號: M1AGLE3000V5-FG484
廠商: Microsemi SoC
文件頁數: 35/166頁
文件大小: 0K
描述: IC FPGA 1KB FLASH 3M 484-FBGA
標準包裝: 60
系列: IGLOOe
邏輯元件/單元數: 75264
RAM 位總計: 516096
輸入/輸出數: 341
門數: 3000000
電源電壓: 1.425 V ~ 1.575 V
安裝類型: 表面貼裝
工作溫度: 0°C ~ 70°C
封裝/外殼: 484-BGA
供應商設備封裝: 484-FPBGA(23x23)
IGLOOe Low Power Flash FPGAs
Revision 13
1-7
Pro I/Os with Advanced I/O Standards
The IGLOOe family of FPGAs features a flexible I/O structure, supporting a range of voltages (1.2 V,
1.5 V, 1.8 V, 2.5 V, 3.0 V wide range, and 3.3 V). IGLOOe FPGAs support 19 different I/O standards,
including single-ended, differential, and voltage-referenced. The I/Os are organized into banks, with eight
banks per device (two per side). The configuration of these banks determines the I/O standards
supported. Each I/O bank is subdivided into VREF minibanks, which are used by voltage-referenced
I/Os. VREF minibanks contain 8 to 18 I/Os. All the I/Os in a given minibank share a common VREF line.
Therefore, if any I/O in a given VREF minibank is configured as a VREF pin, the remaining I/Os in that
minibank will be able to use that reference voltage.
Each I/O module contains several input, output, and enable registers. These registers allow the
implementation of the following:
Single-Data-Rate applications (e.g., PCI 66 MHz, bidirectional SSTL 2 and 3, Class I and II)
Double-Data-Rate applications (e.g., DDR LVDS, B-LVDS, and M-LVDS I/Os for point-to-point
communications, and DDR 200 MHz SRAM using bidirectional HSTL Class II).
IGLOOe banks support M-LVDS with 20 multi-drop points.
Hot-swap (also called hot-plug, or hot-insertion) is the operation of hot-insertion or hot-removal of a card
in a powered-up system.
Cold-sparing (also called cold-swap) refers to the ability of a device to leave system data undisturbed
when the system is powered up, while the component itself is powered down, or when power supplies
are floating.
Wide Range I/O Support
IGLOOe devices support JEDEC-defined wide range I/O operation. IGLOOe devices support both the
JESD8-B specification, covering 3.0 V and 3.3 V supplies, for an effective operating range of 2.7 V to
3.6 V, and JESD8-12 with its 1.2 V nominal, supporting an effective operating range of 1.14 V to 1.575 V.
Wider I/O range means designers can eliminate power supplies or power conditioning components from
the board or move to less costly components with greater tolerances. Wide range eases I/O bank
management and provides enhanced protection from system voltage spikes, while providing the flexibility
to easily run custom voltage applications.
Specifying I/O States During Programming
You can modify the I/O states during programming in FlashPro. In FlashPro, this feature is supported for
PDB files generated from Designer v8.5 or greater. See the FlashPro User’s Guide for more information.
Note: PDB files generated from Designer v8.1 to Designer v8.4 (including all service packs) have
limited display of Pin Numbers only.
1. Load a PDB from the FlashPro GUI. You must have a PDB loaded to modify the I/O states during
programming.
2. From the FlashPro GUI, click PDB Configuration. A FlashPoint – Programming File Generator
window appears.
3. Click the Specify I/O States During Programming button to display the Specify I/O States
During Programming dialog box.
4. Sort the pins as desired by clicking any of the column headers to sort the entries by that header.
Select the I/Os you wish to modify (Figure 1-4 on page 1-8).
5. Set the I/O Output State. You can set Basic I/O settings if you want to use the default I/O settings
for your pins, or use Custom I/O settings to customize the settings for each pin. Basic I/O state
settings:
1 – I/O is set to drive out logic High
0 – I/O is set to drive out logic Low
Last Known State – I/O is set to the last value that was driven out prior to entering the
programming mode, and then held at that value during programming
Z -Tri-State: I/O is tristated
相關PDF資料
PDF描述
M1AGLE3000V5-FGG484 IC FPGA 1KB FLASH 3M 484-FBGA
M1A3PE3000-1FG484I IC FPGA 1KB FLASH 3M 484-FBGA
AMC08DTEF CONN EDGECARD 16POS .100 EYELET
A42MX36-3BGG272I IC FPGA MX SGL CHIP 54K 272-PBGA
A42MX36-3BG272I IC FPGA MX SGL CHIP 54K 272-PBGA
相關代理商/技術參數
參數描述
M1AGLE3000V5-FG484I 功能描述:IC FPGA 1KB FLASH 3M 484-FBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:IGLOOe 標準包裝:1 系列:ProASICPLUS LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:129024 輸入/輸出數:248 門數:600000 電源電壓:2.3 V ~ 2.7 V 安裝類型:表面貼裝 工作溫度:- 封裝/外殼:352-BFCQFP,帶拉桿 供應商設備封裝:352-CQFP(75x75)
M1AGLE3000V5-FG896 功能描述:IC FPGA 1KB FLASH 3M 896-FBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:IGLOOe 標準包裝:1 系列:ProASICPLUS LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:129024 輸入/輸出數:248 門數:600000 電源電壓:2.3 V ~ 2.7 V 安裝類型:表面貼裝 工作溫度:- 封裝/外殼:352-BFCQFP,帶拉桿 供應商設備封裝:352-CQFP(75x75)
M1AGLE3000V5-FG896ES 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOOe Low-Power Flash FPGAs with Flash Freeze Technology
M1AGLE3000V5-FG896I 功能描述:IC FPGA 1KB FLASH 3M 896-FBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:IGLOOe 標準包裝:1 系列:ProASICPLUS LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:129024 輸入/輸出數:248 門數:600000 電源電壓:2.3 V ~ 2.7 V 安裝類型:表面貼裝 工作溫度:- 封裝/外殼:352-BFCQFP,帶拉桿 供應商設備封裝:352-CQFP(75x75)
M1AGLE3000V5-FG896PP 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOOe Low-Power Flash FPGAs with Flash Freeze Technology