參數資料
型號： M25P40-VMN6TG/X
廠商： NUMONYX
元件分類： PROM
英文描述： 512K X 8 SPI BUS SERIAL EEPROM, PDSO8
封裝： 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-8
文件頁數： 4/57頁
文件大?。?/td> 1160K
代理商： M25P40-VMN6TG/X
Operating features
M25P40
12/57
4
Operating features
4.1
Page Programming
To program one data byte, two instructions are required: Write Enable (WREN), which is
one byte, and a Page Program (PP) sequence, which consists of four bytes plus data. This
is followed by the internal Program cycle (of duration tPP).
To spread this overhead, the Page Program (PP) instruction allows up to 256 bytes to be
programmed at a time (changing bits from 1 to 0), provided that they lie in consecutive
addresses on the same page of memory.
For optimized timings, it is recommended to use the Page Program (PP) instruction to
program all consecutive targeted bytes in a single sequence versus using several Page
Program (PP) sequences with each containing only a few bytes (see Page Program (PP),
4.2
Sector Erase and Bulk Erase
The Page Program (PP) instruction allows bits to be reset from 1 to 0. Before this can be
applied, the bytes of memory need to have been erased to all 1s (FFh). This can be
achieved either a sector at a time, using the Sector Erase (SE) instruction, or throughout the
entire memory, using the Bulk Erase (BE) instruction. This starts an internal Erase cycle (of
duration tSE or tBE).
The Erase instruction must be preceded by a Write Enable (WREN) instruction.
4.3
Polling during a Write, Program or Erase cycle
A further improvement in the time to Write Status Register (WRSR), Program (PP) or Erase
(SE or BE) can be achieved by not waiting for the worst case delay (tW, tPP, tSE, or tBE). The
Write In Progress (WIP) bit is provided in the Status Register so that the application program
can monitor its value, polling it to establish when the previous Write cycle, Program cycle or
Erase cycle is complete.
4.4
Active Power, Standby Power and Deep Power-down modes
When Chip Select (S) is Low, the device is selected, and in the Active Power mode.
When Chip Select (S) is High, the device is deselected, but could remain in the Active
Power mode until all internal cycles have completed (Program, Erase, Write Status
Register). The device then goes in to the Standby Power mode. The device consumption
drops to ICC1.
The Deep Power-down mode is entered when the specific instruction (the Deep Power-
down (DP) instruction) is executed. The device consumption drops further to ICC2. The
device remains in this mode until another specific instruction (the Release from Deep
Power-down and Read Electronic Signature (RES) instruction) is executed.
相關PDF資料
PDF描述
M25P40VMF6 4 Mbit Uniform Sector, Serial Flash Memory
M25P40VMF6G 4 Mbit Uniform Sector, Serial Flash Memory
M25P40VMF6P 4 Mbit Uniform Sector, Serial Flash Memory
M25P40VMF6T 4 Mbit Uniform Sector, Serial Flash Memory
M25P40VMF6TG 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
M25P40VMN6TP 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface
M25P40-VMN6TP 功能描述:閃存 SERIAL SECTOR ERASE FLASH 4MEG RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M25P40-VMN6TP/X 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:4 Mbit, low voltage, serial Flash memory with 50 MHz SPI bus interface
M25P40-VMN6TP_NUD 制造商:Micron Technology Inc 功能描述:
M25P40-VMN6TPB 功能描述:IC FLASH 4MBIT 75MHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:Forté™ 標準包裝:2,000 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 異步 存儲容量:256K (32K x 8) 速度:15ns 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:28-TSSOP（0.465"，11.8mm 寬） 供應商設備封裝:28-TSOP 包裝:帶卷 (TR) 其它名稱:71V256SA15PZGI8
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*