- 您現在的位置：買賣IC網 > PDF目錄358974 > M25PE80-VMP6G (意法半導體) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | M25PE80-VMP6G |
| 廠商： | 意法半導體 |
| 元件分類： | FLASH |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 26/43頁 |
| 文件大?。?/td> | 599K |
| 代理商： | M25PE80-VMP6G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
M25PE80
26/43
Sector Erase (SE)
The Sector Erase (SE) instruction sets to 1 (FFh)
all bits inside the chosen sector. Before it can be
accepted, a Write Enable (WREN) instruction
must previously have been executed. After the
Write Enable (WREN) instruction has been decod-
ed, the device sets the Write Enable Latch (WEL).
The Sector Erase (SE) instruction is entered by
driving Chip Select (S) Low, followed by the in-
struction code, and three address Bytes on Serial
Data Input (D). Any address inside the Sector (see
Table 5.
) is a valid address for the Sector Erase
(SE) instruction. Chip Select (S) must be driven
Low for the entire duration of the sequence.
The instruction sequence is shown in
Figure 19.
.
Chip Select (S) must be driven High after the
eighth bit of the last address Byte has been
latched in, otherwise the Sector Erase (SE) in-
struction is not executed. As soon as Chip Select
(S) is driven High, the self-timed Sector Erase cy-
cle (whose duration is t
SE
) is initiated. While the
Sector Erase cycle is in progress, the Status Reg-
ister may be read to check the value of the Write
In Progress (WIP) bit. The Write In Progress (WIP)
bit is 1 during the self-timed Sector Erase cycle,
and is 0 when it is completed. At some unspecified
time before the cycle is complete, the Write Enable
Latch (WEL) bit is reset.
A Sector Erase (SE) instruction applied to a sector
that contains a page that is Hardware or software
Protected is not executed.
Any Sector Erase (SE) instruction, while an Erase,
Program or Write cycle is in progress, is rejected
without having any effects on the cycle that is in
progress.
Figure 19. Sector Erase (SE)
Instruction Sequence
Note: Address bits A23 to A19 are Don’t Care.
24 Bit Address
C
D
AI03751D
S
2
1
3
4
5
6
7
8
9
29 30 31
Instruction
0
23 22
2
0
1
MSB
相關PDF資料 |
PDF描述 |
|---|---|
| M25PE80-VMP6P | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE80-VMP6T | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE80-VMP6TG | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE80-VMP6TP | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE80 | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M25PE80-VMP6P | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:8-Mbit, page-erasable serial flash memory with byte alterability, 75 MHz SPI bus, standard pinout |
| M25PE80-VMP6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit, Low Voltage, Page-Erasable Serial Flash Memory with Byte-Alterability, 50MHz SPI Bus, Standard Pin-out |
| M25PE80-VMP6TG | 功能描述:閃存 SERIAL PAGE ERASE FLASH 8 Mbit Datas RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M25PE80-VMP6TP | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:8-Mbit, page-erasable serial flash memory with byte alterability, 75 MHz SPI bus, standard pinout |
| M25PE80-VMS6G | 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3.3V 8Mbit 1M x 8bit 8ns 8-Pin QFN Tray |
發布緊急采購，3分鐘左右您將得到回復。