- 您現在的位置：買賣IC網 > PDF目錄359053 > M29W800DT90M6T (意法半導體) Low-Power Configurable Multiple-Function Gate 6-SC70 -40 to 85 PDF資料下載
參數資料
| 型號： | M29W800DT90M6T |
| 廠商： | 意法半導體 |
| 英文描述： | Low-Power Configurable Multiple-Function Gate 6-SC70 -40 to 85 |
| 中文描述： | 8兆（1兆x8或512KB的x16插槽，引導塊）3V電源快閃記憶體 |
| 文件頁數： | 12/41頁 |
| 文件大?。?/td> | 219K |
| 代理商： | M29W800DT90M6T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
M29W800DT, M29W800DB
12/41
Table 3. Bus Operations, BYTE = V
IH
Note: X = V
IL
or V
IH
.
COMMAND INTERFACE
All Bus Write operations to the memory are inter-
preted by the Command Interface. Commands
consist of one or more sequential Bus Write oper-
ations. Failure to observe a valid sequence of Bus
Write operations will result in the memory return-
ing to Read mode. The long command sequences
are imposed to maximize data security.
The address used for the commands changes de-
pending on whether the memory is in 16-bit or 8-
bit mode. See either Table 4, or 5, depending on
the configuration that is being used, for a summary
of the commands.
Read/Reset Command.
The Read/Reset com-
mand returns the memory to its Read mode where
it behaves like a ROM or EPROM, unless other-
wise stated. It also resets the errors in the Status
Register. Either one or three Bus Write operations
can be used to issue the Read/Reset command.
The Read/Reset Command can be issued, be-
tween Bus Write cycles before the start of a pro-
gram or erase operation, to return the device to
read mode. Once the program or erase operation
has started the Read/Reset command is no longer
accepted. The Read/Reset command will not
abort an Erase operation when issued while in
Erase Suspend.
Auto Select Command.
The Auto Select com-
mand is used to read the Manufacturer Code, the
Device Code and the Block Protection Status.
Three consecutive Bus Write operations are re-
quired to issue the Auto Select command. Once
the Auto Select command is issued the memory
remains in Auto Select mode until a Read/Reset
command is issued. Read CFI Query and Read/
Reset commands are accepted in Auto Select
mode, all other commands are ignored.
From the Auto Select mode the Manufacturer
Code can be read using a Bus Read operation
with A0 = V
IL
and A1 = V
IL
. The other address bits
may be set to either V
IL
or V
IH
. The Manufacturer
Code for STMicroelectronics is 0020h.
The Device Code can be read using a Bus Read
operation with A0 = V
IH
and A1 = V
IL
. The other
address bits may be set to either V
IL
or V
IH
. The
Device Code for the M29W800DT is 22D7h and
for the M29W800DB is 225Bh.
The Block Protection Status of each block can be
read using a Bus Read operation with A0 = V
IL
,
A1 = V
IH
, and A12-A18 specifying the address of
the block. The other address bits may be set to ei-
ther V
IL
or V
IH
. If the addressed block is protect-
ed then 01h is output on Data Inputs/Outputs
DQ0-DQ7, otherwise 00h is output.
Program Command.
The Program command
can be used to program a value to one address in
the memory array at a time. The command re-
quires four Bus Write operations, the final write op-
eration latches the address and data in the internal
state machine and starts the Program/Erase Con-
troller.
If the address falls in a protected block then the
Program command is ignored, the data remains
unchanged. The Status Register is never read and
no error condition is given.
During the program operation the memory will ig-
nore all commands. It is not possible to issue any
command to abort or pause the operation. Typical
program times are given in Table 6. Bus Read op-
erations during the program operation will output
the Status Register on the Data Inputs/Outputs.
See the section on the Status Register for more
details.
Operation
E
G
W
Address Inputs
A0-A18
Data Inputs/Outputs
DQ15A–1, DQ14-DQ0
Bus Read
V
IL
V
IL
V
IH
Cell Address
Data Output
Bus Write
V
IL
V
IH
V
IL
Command Address
Data Input
Output Disable
X
V
IH
V
IH
X
Hi-Z
Standby
V
IH
X
X
X
Hi-Z
Read Manufacturer
Code
V
IL
V
IL
V
IH
A0 = V
IL
, A1 = V
IL
, A9 = V
ID
,
Others V
IL
or V
IH
0020h
Read Device Code
V
IL
V
IL
V
IH
A0 = V
IH
, A1 = V
IL
, A9 = V
ID
,
Others V
IL
or V
IH
22D7h (M29W800DT)
225Bh (M29W800DB)
相關PDF資料 |
PDF描述 |
|---|---|
| M29W800DT90N1T | Low-Power Configurable Multiple-Function Gate 6-SC70 -40 to 85 |
| M29W800DT90N6T | Low-Power Configurable Multiple-Function Gate 6-SC70 -40 to 85 |
| M29W800DT90ZA1T | Low-Power Configurable Multiple-Function Gate 6-SC70 -40 to 85 |
| M29W800DT90ZA6T | Low-Power Configurable Multiple-Function Gate 6-SC70 -40 to 85 |
| M29W800DB90M1T | 8 Mbit (1Mb x8 or 512Kb x16, Boot Block) 3V Supply Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M29W800DT90N1 | 功能描述:閃存 8 MBIT (1MB) 3V SUPPLY RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M29W800DT90N6 | 功能描述:IC FLASH 8MBIT 90NS 48TSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:150 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (2 x 256 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-DFN（2x3） 包裝:管件 產品目錄頁面:1445 (CN2011-ZH PDF) |
| M29W800FB70N3E | 制造商:Micron Technology Inc 功能描述: 制造商:Micron Technology Inc 功能描述:IC FLASH 8MBIT 70NS 48TSOP |
| M29W800FB70N3F | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel 制造商:Micron Technology Inc 功能描述:IC FLASH 8MBIT 70NS 48TSOP |
| M29W800FB70ZA3SE | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 8MBIT 70NS 48TFBGA |
發布緊急采購，3分鐘左右您將得到回復。