Rev.1.00
May 18, 2004
page 253 of 296
M306V7MG/MH/MJ/MJA-XXXFP, M306V7FG/FH/FJ/FJAFP
Table 5.3.1 Electrical characteristics (referenced to VCCI=3.3V, VCCE=5.0V, VSS = 0 V at Ta = 25 oC,
f(XIN) = 16 MHz unless otherwise specified)
5.3 Electrical Characteristics
VOH
VOL
LOW output voltage
IIH
I IL
HIGH output voltage
P67, P72, P93,P94
VT+-VT-
V
(Note 1)
V
0.2
0.6
V
0.2
0.8
V
0.2
1.2
V
10.0
A
10.0
A
RESET
VCCI -1.5
(Note 2)
(Note 3)
(Note 4)
VCCE-1.5
IOH= –5mA
HOLD, RDY, TB0IN to TB2IN,
INT0, INT1, CTS0, CTS2,
CLK0, RXD0, HSYNC, VSYNC,
HC0, HC1, XIN
VI=3.3V
VI=5.0V
VI=0V
–10.0
RPULLUP
Icc
k
200
A
mA
2
VI=0V
167.0
40
60
f(XCIN) = 32kHz
In the weight
100
A
f(XIN) = 16 MHz
Square wave, division by 8
Square wave,
no division
15
mA
90
120
RBS
VCCE=5.0V
130
M
M
6.0
3.0
50.0
30.0
IOL=5mA
1.5
V
VOL
LOW output voltage P67, P70,P71, P72 ,P93 ,P94
IOL=6mA
0.6
V
SCL1, SCL2, SCL3, CLK2,
SDA1, SDA2, SDA3, RXD2
400
50
0.5
mA
I2C-BUS BUS switch connection resistor
(between SCL1 and SCL2, SDA1 and SDA2)
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to 47, P50 to P57,
P60 to P63, P73 to P77,P82,
P83, P86, P87, P90 to P92,
P102 to P107, XIN, RESET, CNVSS,
BYTE, OSC1, Hsync, Vsync
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to 47, P50 to P57,
P60 to P63, P73 to P77,
2, P83, P86, P87,
P90 to P92, P102 to P107,
R, G, B, OUT1, OUT2
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to 47, P50 to P57,
P60 to P63, P73 to P77,
P82, P83, P86, P87,
P90 to P92, P102 to P107,
R, G, B, OUT1, OUT2
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to P47, P50 to P57,
P60 to P63, P67, P70 to P77,P82,
P83, P86, P87, P90 to P94,
P102 to P107, XIN, RESET, CNVSS,
BYTE, OSC1, Hsync, Vsync
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to P47, P50 to P57,
P60 to P63, P67, P72 to P77,P82,
P83, P86, P87, P90 to P94,
P102 to P107,
RfXIN
Feedback resistor XIN
RfXCIN
Feedback resistor XCIN
Power supply current
In single-chip
mode, the
output pins
are open and
other pins are
VSS
Ta=25
°C when
clock is stopped
Ta = 70
°C when
clock is stopped
OSD (40MHz)ON,
Data slicer ON
OSD OFF,
Data slicer OFF
OSD OFF,
Data slicer OFF
Hysteresis
HIGH input
current
HIGH input
current
LOW input
current
Pull-up resistor
Symbol
Measuring condition
Parameter
Standard
Typ.
Unit
Min.
Max.
IIH
P67, P70, P71,
P72, P93, P94
Notes1: The minimum value standard for every VOH serves as a straight line which connected (IOH = -5 mA, VOH = VCCI-1.5 V) and (IOH = 0 mA, VOH = VCCI).
2: The minimum value standard for every VOH serves as a straight line which connected (IOH = -5 mA, VOH = VCCE-1.5 V) and (IOH = 0 mA, VOH = VCCE).
3: The maximum value standard for every VOL serves as a straight line which connected (IOH = 5 mA, VOL = 1.5 V) and (IOL = 0 mA, VOL = 0.0 V).
4: The maximum value standard for every VOL serves as a straight line which connected (IOH = 6 mA, VOL = 0.6 V) and (IOL = 0 mA, VOL = 0.0 V).