參數資料
型號: M34506E4FP
元件分類: 微控制器/微處理器
英文描述: 4-BIT, OTPROM, MICROCONTROLLER, PDSO20
封裝: 5.30 X 12.60 MM, 1.27 MM PITCH, PLASTIC, SOP-20
文件頁數: 75/114頁
文件大?。?/td> 937K
代理商: M34506E4FP
Rev.2.00
Aug 28, 2006
page 61 of 119
7643 Group
REJ03B0054-0200
(5) Low power dissipation mode
The low power dissipation operation can be realized by stopping
the main clock XIN when using f(XCIN) as the internal system
clock. To stop the main clock, set the Main Clock (XIN-XOUT)
Stop Bit of the CPU mode register A to “1”.
The low power dissipation operation can be realized by disabling
the reversed amplifier when inputting external clocks to the XIN
pin or XCIN pin. To disable the reversed amplifier, set the XCOUT
Oscillation Drive Disable Bit (CCR5) or XOUT Oscillation Drive
Disable Bit (CCR6) of the clock control register to “1”.
Oscillation Control
(1) Stop mode
If the STP instruction is executed, the internal clock
φ stops at “H”
level, and XIN and XCIN oscillators stop. Then the timer 1 is set to
“FF16” and the internal clock
φ divided by 8 is automatically se-
lected as its count source. Additionally, the timer 2 is set to “0116
and the timer 1’s output is automatically selected as its count
source.
Set the Timer 1 and Timer 2 Interrupt Enable Bits to disabled (“0”)
before executing the STP instruction. When using an external in-
terrupt to release the stop mode, set the Interrupt Enable Bit to be
used to enabled (“1”) and the Interrupt Disable Flag (I) to “0”.
Oscillator restarts at reset or when an external interrupt including
USB resume interrupts is received, but the internal clock
φ re-
mains at “H” until the timer 2 underflows. The internal clock
φ is
supplied for the first time when the timer 2 underflows. Therefore
make sure not to set the Timer 1 Interrupt Request Bit and Timer
2 Interrupt Request Bit to “1” before the STP instruction stops the
oscillator.
(2) Wait mode
If the WIT instruction is executed, the internal clock
φ stops at “H”
level, but the oscillator does not stop. The internal clock
φ restarts
at reset or when an interrupt is received. Since the oscillator does
not stop, normal operation can be started immediately after the in-
ternal clock
φ is restarted.
Set the Interrupt Enable Bit to be used to release the wait mode to
enabled (“1”) and the Interrupt Disable Flag (I) to “0”.
Fig. 58 Structure of clock control register
Clock control register (address 001F16)
CCR
Reserved bits (“0” at read/write)
Fix to “0”.
XCOUT oscillation drive disable bit (CCR5)
0: XCOUT oscillation drive is enabled.
(When XCIN oscillation is enabled.)
1: XCOUT oscillation drive is disabled.
XOUT oscillation drive disable bit (CCR6)
0: XOUT oscillation drive is enabled.
(When XIN oscillation is enabled.)
1: XOUT oscillation drive is disabled.
XIN divider select bit (CCR7)
Valid when CPMA6, CPMA7 = “00”
0: f(XIN)/2 is used for the system clock.
1: f(XIN) is used for the system clock.
b0
b7
000 0 0
相關PDF資料
PDF描述
M34508G4HFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
M34508G4GP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
M34508G4H-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
M34508G4-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
M34508G4FP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
相關代理商/技術參數
參數描述
M34506M2 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34506M2-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 4500 SERIES
M34506M4 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34506M4-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 4500 SERIES
M34507E4FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER