- 您現在的位置：買賣IC網 > PDF目錄69010 > M34509G4-XXXFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO24 PDF資料下載
參數資料
| 型號： | M34509G4-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO24 |
| 封裝： | 5.30 X 10.10 MM, 0.80 MM PITCH, PLASTIC, SSOP-24 |
| 文件頁數： | 115/145頁 |
| 文件大小： | 1060K |
| 代理商： | M34509G4-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁當前第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁
4509 Group
Rev.1.03
2009.07.27
page 69 of 140
REJ03B0147-0103
5. Setup for I/O ports
Setup I/O ports using hardware and software as follows:
<Hardware>
Connect a resistor of 100 or more to an I/O port in series.
<Software>
As for an input port, read data several times by a program for
checking whether input levels are equal or not.
As for an output port or an I/O port, since the output data may re-
verse because of noise, rewrite data to its port latch at fixed
periods.
Rewrite data to pull-up control registers at fixed periods.
6. Providing of watchdog timer function by software
If a microcomputer runs away because of noise or others, it can be
detected by a software watchdog timer and the microcomputer can
be reset to normal operation. This is equal to or more effective than
program runaway detection by a hardware watchdog timer. The fol-
lowing shows an example of a watchdog timer provided by software.
In the following example, to reset a microcomputer to normal opera-
tion, the main routine detects errors of the interrupt processing
routine and the interrupt processing routine detects errors of the
main routine.
This example assumes that interrupt processing is repeated multiple
times in a single main routine processing.
4. Oscillator concerns
Take care to prevent an oscillator that generates clocks for a micro-
computer operation from being affected by other signals.
(1) Keeping oscillator away from large current signal lines
Install a microcomputer (and especially an oscillator) as far as pos-
sible from signal lines where a current larger than the tolerance of
current value flows.
<Reason>
In the system using a microcomputer, there are signal lines for con-
trolling motors, LEDs, and thermal heads or others. When a large
current flows through those signal lines, strong noise occurs be-
cause of mutual inductance.
(2) Installing oscillator away from signal lines where potential levels
change frequently
Install an oscillator and a connecting pattern of an oscillator away
from signal lines where potential levels change frequently. Also, do
not cross such signal lines over the clock lines or the signal lines
which are sensitive to noise.
<Reason>
Signal lines where potential levels change frequently (such as the
CNTR pin signal line) may affect other lines at signal rising edge or
falling edge. If such lines cross over a clock line, clock waveforms
may be deformed, which causes a microcomputer failure or a pro-
gram runaway.
Fig. 69 Wiring for a large current signal line
XIN
XOUT
VSS
M
Microcomputer
Mutual inductance
Large
current
GND
(3) Oscillator protection using Vss pattern
As for a two-sided printed circuit board, print a Vss pattern on the
underside (soldering side) of the position (on the component side)
where an oscillator is mounted.
Connect the Vss pattern to the microcomputer Vss pin with the
shortest possible wiring. Besides, separate this Vss pattern from
other Vss patterns.
Fig. 71 Vss pattern on the underside of an oscillator
XIN
XOUT
VSS
An example of VSS patterns on the
underside of a printed circuit board
Oscillator wiring
pattern example
Separate the VSS line for oscillation from other VSS lines
XIN
XOUT
VSS
CNTR
Do not cross
N.G.
Fig. 70 Wiring to a signal line where potential levels change fre-
quently
相關PDF資料 |
PDF描述 |
|---|---|
| M34509G4H-XXXFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO24 |
| M34510M4A-XXXSP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDIP32 |
| M34510M2A-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO36 |
| M34510E8-XXXFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36 |
| M34513M6-XXXFP | 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34509T2-CPE | 功能描述:DEV TOOL COMPACT EMULATOR: 4508/ RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:* |
| M34512M2 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34512M2-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34512M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34512M4-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。