參數資料
型號： M34C02-W-WMB6TG
廠商： 意法半導體
英文描述： 2 Kbit Serial IC Bus EEPROM for DIMM serial presence detect
中文描述： 2千位串行IC總線的EEPROM內存串行存在檢測
文件頁數： 17/31頁
文件大?。?/td> 162K
代理商： M34C02-W-WMB6TG
M34C02-W, M34C02-L, M34C02-R
Device operation
17/31
3.8
Read Operations
Read operations are performed independently of whether hardware or software protection
has been set.
The device has an internal address counter which is incremented each time a byte is read.
3.8.1
Random Address Read
A dummy Write is first performed to load the address into this address counter (as shown in
Figure 10
) but
without
sending a Stop condition. Then, the bus master sends another Start
condition, and repeats the Device Select Code, with the RW bit set to 1. The device
acknowledges this, and outputs the contents of the addressed byte. The bus master must
not
acknowledge the byte, and terminates the transfer with a Stop condition.
3.8.2
Current Address Read
For the Current Address Read operation, following a Start condition, the bus master only
sends a Device Select Code with the RW bit set to 1. The device acknowledges this, and
outputs the byte addressed by the internal address counter. The counter is then
incremented. The bus master terminates the transfer with a Stop condition, as shown in
Figure 10
,
without
acknowledging the byte.
3.8.3
Sequential Read
This operation can be used after a Current Address Read or a Random Address Read. The
bus master
does
acknowledge the data byte output, and sends additional clock pulses so
that the device continues to output the next byte in sequence. To terminate the stream of
bytes, the bus master must
not
acknowledge the last byte, and
must
generate a Stop
condition, as shown in
Figure 10
.
The output data comes from consecutive addresses, with the internal address counter
automatically incremented after each byte output. After the last memory address, the
address counter ‘rolls-over’, and the device continues to output data from memory address
00h.
3.8.4
Acknowledge in Read Mode
For all Read commands, the device waits, after each byte read, for an acknowledgment
during the 9
th
bit time. If the bus master does not drive Serial Data (SDA) Low during this
time, the device terminates the data transfer and switches to its Stand-by mode.
相關PDF資料
PDF描述
M34E02-FDW1T 2 Kbit Serial IC Bus EEPROM Serial Presence Detect for DDR2 DIMMs
M34S32BN CAP 220UF 35V ELECT LXY RAD
M34S32MN 32K Serial I2C Bus EEPROM With User-Defined Read-Only Block and 32-Byte OTP Page
M34S32MN1T 32K Serial I2C Bus EEPROM With User-Defined Read-Only Block and 32-Byte OTP Page
M34S32MN5T 32K Serial I2C Bus EEPROM With User-Defined Read-Only Block and 32-Byte OTP Page
相關代理商/技術參數
參數描述
M34C106K125AZSS 功能描述:鉭質電容器-濕式 10uF 125volts 10% C Case RoHS:否 制造商:Vishay/Tansitor 電容:2800 uF 電壓額定值:35 V ESR:0.35 Ohms 容差:20 % 端接類型:Axial 工作溫度范圍:- 55 C to + 85 C 制造商庫存號:T4 Case 外殼直徑:9.52 mm 外殼長度:26.97 mm 外殼寬度: 外殼高度: 系列:STE 產品:Tantalum Wet Hermetically Sealed 封裝:Bulk
M34C106K125BZSS 功能描述:鉭質電容器-濕式 10uF 125volts 10% C Case RoHS:否 制造商:Vishay/Tansitor 電容:2800 uF 電壓額定值:35 V ESR:0.35 Ohms 容差:20 % 端接類型:Axial 工作溫度范圍:- 55 C to + 85 C 制造商庫存號:T4 Case 外殼直徑:9.52 mm 外殼長度:26.97 mm 外殼寬度: 外殼高度: 系列:STE 產品:Tantalum Wet Hermetically Sealed 封裝:Bulk
M34C106M125AZSS 制造商:Vishay Sprague 功能描述:- Bulk
M34C106M125BZSS 制造商:Vishay Sprague 功能描述:- Bulk
M34C107K030AZSS 功能描述:鉭質電容器-濕式 100uF 30volts 10% C Case RoHS:否 制造商:Vishay/Tansitor 電容:2800 uF 電壓額定值:35 V ESR:0.35 Ohms 容差:20 % 端接類型:Axial 工作溫度范圍:- 55 C to + 85 C 制造商庫存號:T4 Case 外殼直徑:9.52 mm 外殼長度:26.97 mm 外殼寬度: 外殼高度: 系列:STE 產品:Tantalum Wet Hermetically Sealed 封裝:Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*