- 您現在的位置：買賣IC網 > PDF目錄359056 > M36DR432CA85ZA6T (意法半導體) 32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256K x16 SRAM, Multiple Memory Product PDF資料下載
參數資料
| 型號： | M36DR432CA85ZA6T |
| 廠商： | 意法半導體 |
| 英文描述： | 32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256K x16 SRAM, Multiple Memory Product |
| 中文描述： | 32兆位的2Mb x16插槽，雙行，頁閃存和4兆位256K x16的SRAM，多個存儲產品 |
| 文件頁數： | 21/52頁 |
| 文件大小： | 834K |
| 代理商： | M36DR432CA85ZA6T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
21/52
M36DR432AD, M36DR432BD
Table 10. Flash Lock Status
Note: 1.
The lock status is defined by the write protect pin and by DQ1 (‘1’ for a locked-down block) and DQ0 (‘1’ for a locked block) as read
in the Auto Select command with A1 = V
IH
and A0 = V
IL
.
2. All blocks are locked at power-up, so the default configuration is 001 or 101 according to WPF status.
3. A WPF transition to V
IH
on a locked block will restore the previous DQ0 value, giving a 111 or 110.
Flash Status Register
The Status Register provides information on the
current or previous Program or Erase operations.
Bus Read operations from any address within the
bank, always read the Status Register during Pro-
gram and Erase operations.
The various bits convey information about the sta-
tus and any errors of the operation.
The bits in the Status Register are summarized in
Table 12, Status Register Bits. Refer to Tables 11
and 12 in conjunction with the following text de-
scriptions.
Data Polling Bit (DQ7).
When Program opera-
tions are in progress, the Data Polling bit outputs
the complement of the bit being programmed on
DQ7. For a Double Word Program operation, it is
the complement of DQ7 for the last Word written to
the Command Interface.
During an Erase operation, it outputs a ’0’. After
completion of the operation, DQ7 will output the bit
last programmed or a ’1’ after erasing.
Data Polling is valid and only effective during P/
E.C. operation, that is after the fourth WF pulse for
programming or after the sixth WF pulse for erase.
It must be performed at the address being pro-
grammed or at an address within the block being
erased. See Figure 22 for the Data Polling flow-
chart and Figure 13 for the Data Polling wave-
forms.
DQ7 will also flag an Erase Suspend by switching
from ’0’ to ’1’ at the start of the Erase Suspend. In
order to monitor DQ7 in the Erase Suspend mode
an address within a block being erased must be
provided. DQ7 will output ’1’ if the read is attempt-
ed on a block being erased and the data value on
other blocks. During a program operation in Erase
Suspend, DQ7 will have the same behavior as in
the normal program.
Toggle Bit (DQ6).
When Program or Erase oper-
ations are in progress, successive attempts to
read DQ6 will output complementary data. DQ6
will toggle following the toggling of either GF or EF.
The operation is completed when two successive
reads give the same output data. The next read
will output the bit last programmed or a ’1’ after
erasing.
The Toggle Bit DQ6 is valid only during P/E.C. op-
erations, that is after the fourth WF pulse for pro-
gramming or after the sixth WF pulse for Erase.
DQ6 will be set to ’1’ if a read operation is attempt-
ed on an Erase Suspend block. When erase is
suspended DQ6 will toggle during programming
operations in a block different from the block in
Erase Suspend.
See Figure 16 for Toggle Bit flowchart and Figure
14 for Toggle Bit waveforms.
Toggle Bit (DQ2).
Toggle Bit DQ2, together with
DQ6, can be used to determine the device status
during erase operations.
During Erase Suspend a read from a block being
erased will cause DQ2 to toggle. A read from a
block not being erased will output data. DQ2 will
be set to '1' during program operation and to ‘0’ in
erase operation. If a read operation is addressed
to a block where an erase error has occurred, DQ2
will toggle.
Current
Protection Status
(1)
(WPF, DQ1, DQ0)
Next Protection Status
(1)
(WPF, DQ1, DQ0)
Current State
Program/Erase
Allowed
After
Block Lock
Command
After
Block Unlock
Command
After Block
Lock-Down
Command
After
WPF transition
1,0,0
yes
1,0,1
1,0,0
1,1,1
0,0,0
1,0,1
(2)
no
1,0,1
1,0,0
1,1,1
0,0,1
1,1,0
yes
1,1,1
1,1,0
1,1,1
0,1,1
1,1,1
no
1,1,1
1,1,0
1,1,1
0,1,1
0,0,0
yes
0,0,1
0,0,0
0,1,1
1,0,0
0,0,1
(2)
no
0,0,1
0,0,0
0,1,1
1,0,1
0,1,1
no
0,1,1
0,1,1
0,1,1
1,1,1 or 1,1,0
(3)
相關PDF資料 |
PDF描述 |
|---|---|
| M36DR432B120ZA6C | 32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256K x16 SRAM, Multiple Memory Product |
| M36DR432BD10ZA6T | 32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256Kb x16 SRAM, Multiple Memory Product |
| M36DR432BD12ZA6T | 32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256Kb x16 SRAM, Multiple Memory Product |
| M36DR432DZA | 32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256K x16 SRAM, Multiple Memory Product |
| M36DR432-ZAT | 32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256K x16 SRAM, Multiple Memory Product |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M36DR432CZA | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256K x16 SRAM, Multiple Memory Product |
| M36DR432D | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256K x16 SRAM, Multiple Memory Product |
| M36DR432DA10ZA6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256K x16 SRAM, Multiple Memory Product |
| M36DR432DA85ZA6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256K x16 SRAM, Multiple Memory Product |
| M36DR432DZA | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32 Mbit 2Mb x16, Dual Bank, Page Flash Memory and 4 Mbit 256K x16 SRAM, Multiple Memory Product |
發布緊急采購，3分鐘左右您將得到回復。