參數資料
型號： M37534E8SP
廠商： Renesas Technology Corp.
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 27/55頁
文件大?。?/td> 610K
代理商： M37534E8SP
7534 Group
Rev.2.00
Jun 21, 2004
page 33 of 54
REJ03B0099-0200Z
Watchdog Timer
The watchdog timer gives a means for returning to a reset status
when the program fails to run on its normal loop due to a runaway.
The watchdog timer consists of an 8-bit watchdog timer H and an 8-
bit watchdog timer L, being a 16-bit counter.
Standard operation of watchdog timer
The watchdog timer stops when the watchdog timer control register
(address 003916) is not set after reset. Writing an optional value to
the watchdog timer control register (address 003916) causes the
watchdog timer to start to count down. When the watchdog timer H
underflows, an internal reset occurs. Accordingly, it is programmed
that the watchdog timer control register (address 003916) can be set
before an underflow occurs.
When the watchdog timer control register (address 003916) is read,
the values of the high-order 6-bit of the watchdog timer H, STP in-
struction disable bit and watchdog timer H count source selection bit
are read.
Initial value of watchdog timer
By a reset or writing to the watchdog timer control register (address
003916), the watchdog timer H is set to “FF16” and the watchdog
timer L is set to “FF16”.
Operation of watchdog timer H count source selection bit
A watchdog timer H count source can be selected by bit 7 of the
watchdog timer control register (address 003916). When this bit is
“0”, the count source becomes a watchdog timer L underflow signal.
The detection time is 174.763 ms at f(XIN)=6 MHz.
When this bit is “1”, the count source becomes f(XIN)/16. In this
case, the detection time is 683 s at f(XIN)=6 MHz.
This bit is cleared to “0” after reset.
Operation of STP instruction disable bit
When the watchdog timer is in operation, the STP instruction can be
disabled by bit 6 of the watchdog timer control register (address
003916).
When this bit is “0”, the STP instruction is enabled.
When this bit is “1”, the STP instruction is disabled, and an internal
reset occurs if the STP instruction is executed.
Once this bit is set to “1”, it cannot be changed to “0” by program.
This bit is cleared to “0” after reset.
Fig. 38 Block diagram of watchdog timer
Fig. 39 Structure of watchdog timer control register
XIN
Data bus
“0”
“1”
1/16
Watchdog timer H count
source selection bit
Reset
circuit
STP Instruction Disable Bit
Watchdog timer H (8)
Write “FF16” to the
watchdog timer
control register
Internal reset
RESET
Watchdog timer L (8)
STP Instruction
Write “FF16” to the
watchdog timer
control register
Watchdog timer control register(address 0039 16)
WDTCON
Watchdog timer H (read-only for high-order 6-bit)
STP instruction disable bit
0 : STP instruction enabled
1 : STP instruction disabled
Watchdog timer H count source selection bit
0 : Watchdog timer L underflow
1 : f(XIN)/16
b7
b0
相關PDF資料
PDF描述
M378T6453FZ3-CD5 64M X 64 DDR DRAM MODULE, 0.5 ns, DMA240
M38030F8-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38030F8-XXXKP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38030F8L-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38030F8L-XXXKP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M37534M4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37534M4-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37534M4-XXXGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37534M4-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37534RSS 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*