- 您現在的位置：買賣IC網 > PDF目錄45043 > M38207E8-XXXHP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M38207E8-XXXHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 0.50 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 25/69頁 |
| 文件大小： | 944K |
| 代理商： | M38207E8-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
Rev.4.01
Nov 14, 2003
page 31 of 136
3803/3804 Group
INTERRUPTS
The 3803 group’s interrupts are a type of vector and occur by 16
sources among 21 sources: eight external, twelve internal, and
one software.
The 3804 group’s interrupts occur by 16 sources among 23
sources: nine external, thirteen internal, and one software.
Interrupt Control
Each interrupt is controlled by an interrupt request bit, an interrupt
enable bit, and the interrupt disable flag except for the software in-
terrupt set by the BRK instruction. An interrupt occurs if the
corresponding interrupt request and enable bits are “1” and the in-
terrupt disable flag is “0”.
Interrupt enable bits can be set or cleared by software.
Interrupt request bits can be cleared by software, but cannot be
set by software.
The reset and the BRK instruction cannot be disabled with any
flag or bit. The I (interrupt disable) flag disables all interrupts ex-
cept the reset and the BRK instruction interrupt.
When several interrupt requests occur at the same time, the inter-
rupts are received according to priority.
Interrupt Operation
By acceptance of an interrupt, the following operations are auto-
matically performed:
1. The contents of the program counter and the processor status
register are automatically pushed onto the stack.
2. The interrupt disable flag is set and the corresponding interrupt
request bit is cleared.
3. The interrupt jump destination address is read from the vector
table into the program counter.
Interrupt Source Selection
Which of each combination of the following interrupt sources can
be selected by the interrupt source selection register (address
003916).
1. INT0 or Timer Z
2. Serial I/O1 transmission or SCL, SDA (for 3804 group)
3. CNTR0 or SCL, SDA (for 3804 group)
4. CNTR1 or Serial I/O3 reception
5. Serial I/O2 or Timer Z
6. INT2 or I2C (for 3804 group)
7. INT4 or CNTR2
8. A-D converter or serial I/O3 transmission
External Interrupt Pin Selection
The occurrence sources of the external interrupt INT0 and INT4
can be selected from either input from INT00 and INT40 pin, or in-
put from INT01 and INT41 pin by the INT0, INT4 interrupt switch bit
of interrupt edge selection register (bit 6 of address 003A16).
s Notes
When setting the followings, the interrupt request bit may be set to
“1”.
When switching external interrupt active edge
Related register: Interrupt edge selection register (address 3A16)
Timer XY mode register (address 2316)
Timer Z mode register (address 2A16)
I2C start/stop condition control register
(address 1616) (3804 group only)
When switching interrupt sources of an interrupt vector address
where two or more interrupt sources are allocated
Related register: Interrupt source selection register
(address 3916)
When not requiring for the interrupt occurrence synchronized with
these setting, take the following sequence.
Set the corresponding interrupt enable bit to “0” (disabled).
Set the interrupt edge select bit or the interrupt source select bit.
Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
Set the corresponding interrupt enable bit to “1” (enabled).
相關PDF資料 |
PDF描述 |
|---|---|
| M38207M8-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| M38203E4FS | 8-BIT, UVPROM, 4 MHz, MICROCONTROLLER, CQCC80 |
| M38203M4LXXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| M38207E8GP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| M38207E8GP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38207M8 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38207M8-051 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER |
| M38207M8-107HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER |
| M38207M8-117HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER |
| M38207M8-501FP | 制造商:Mitsubishi Electric 功能描述:MicroController, 8-Bit, 80 Pin, Plastic, QFP 制造商:Renesas Electronics Corporation 功能描述:MicroController, 8-Bit, 80 Pin, Plastic, QFP |
發布緊急采購，3分鐘左右您將得到回復。