- 您現在的位置：買賣IC網 > PDF目錄45045 > M38257E8FS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC100 PDF資料下載
參數資料
| 型號： | M38257E8FS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC100 |
| 封裝： | 0.65 MM PITCH, GLASS SEALED, CERAMIC, LCC-100 |
| 文件頁數： | 19/70頁 |
| 文件大小： | 994K |
| 代理商： | M38257E8FS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3825 Group
26
Timer Y
Timer Y is a 16-bit timer that can be selected in one of four modes.
(1) Timer mode
The timer counts f(XIN)/16 (or f(XCIN)/16 in low-speed mode).
(2) Period measurement mode
CNTR1 interrupt request is generated at rising/falling edge of
CNTR1 pin input signal. Simultaneously, the value in timer Y latch
is reloaded in timer Y and timer Y continues counting down. Ex-
cept for the above-mentioned, the operation in period measure-
ment mode is the same as in timer mode.
The timer value just before the reloading at rising/falling of CNTR1
pin input signal is retained until the timer Y is read once after the
reload.
The rising/falling timing of CNTR1 pin input signal is found by
CNTR1 interrupt. When using a timer in this mode, set the corre-
sponding port P55 direction register to input mode.
(3) Event counter mode
The timer counts signals input through the CNTR1 pin.
Except for this, the operation in event counter mode is the same
as in timer mode. When using a timer in this mode, set the corre-
sponding port P55 direction register to input mode.
(4) Pulse width HL continuously measure-
ment mode
CNTR1 interrupt request is generated at both rising and falling
edges of CNTR1 pin input signal. Except for this, the operation in
pulse width HL continuously measurement mode is the same as in
period measurement mode. When using a timer in this mode, set
the corresponding port P55 direction register to input mode.
sNote on CNTR1 interrupt active edge selection
CNTR1 interrupt active edge depends on the CNTR1 active edge
switch bit. However, in pulse width HL continuously measurement
mode, CNTR1 interrupt request is generated at both rising and
falling edges of CNTR1 pin input signal regardless of the setting of
CNTR1 active edge switch bit.
Fig. 21 Structure of timer Y mode register
Timer Y mode register
(TYM : address 002816)
b7
b0
Not used (return “0” when read)
Timer Y operating mode bits
b5 b4
0
0 : Timer mode
0
1 : Period measurement mode
1
0 : Event counter mode
1
1 : Pulse width HL continuously
measurement mode
CNTR1 active edge switch bit
0 : Count at rising edge in event counter mode
Measure the falling edge to falling edge
period in period measurement mode
Falling edge active for CNTR1 interrupt
1 : Count at falling edge in event counter mode
Measure the rising edge period in period
measurement mode
Rising edge active for CNTR1 interrupt
Timer Y stop control bit
0 : Count start
1 : Count stop
相關PDF資料 |
PDF描述 |
|---|---|
| M38257E8FP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M38258MCMXXXHP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M38258MCDXXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M38259EFHP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M38259EFFP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38258MCM084 | 制造商:Panasonic Industrial Company 功能描述:IC |
| M3826 | 功能描述:電纜固定件和配件 LTRSCG 1000 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度: |
| M3826 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 2COND 16AWG BLK 1000' |
| M3826 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 2COND 16AWG BLK 500' |
| M3826 BK005 | 制造商:Alpha Wire Company 功能描述:CBL 2COND 16AWG BLK 100' |
發布緊急采購，3分鐘左右您將得到回復。