參數資料
型號： M38257E8GP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100
文件頁數： 46/73頁
文件大?。?/td> 1323K
代理商： M38257E8GP
Rev.2.02
Jun 19, 2007
page 48 of 73
REJ03B0146-0202
3823 Group
WATCHDOG TIMER
The watchdog timer gives a mean of returning to the reset status
when a program cannot run on a normal loop (for example, be-
cause of a software run-away). The watchdog timer consists of an
8-bit counter.
Initial Value of Watchdog Timer
At reset or writing to the watchdog timer control register, each
watchdog timer is set to “FF16.” Instructions such as STA, LDM
and CLB to generate the write signals can be used.
The written data in bits 0 to 5 are not valid, and the above values
are set.
Bits 7 and 6 can be rewritten only once after reset.
After rewriting it is disable to write any data to this bit. These bits
become “0” after reset.
Standard Operation of Watchdog Timer
The watchdog timer is in the stop state at reset and the watchdog
timer starts to count down by writing an optional value in the
watchdog timer control register. An internal reset occurs at an un-
derflow of the watchdog timer. Then, reset is released after the
reset release time is elapsed, the program starts from the reset
vector address. Normally, writing to the watchdog timer control
register before an underflow of the watchdog timer is pro-
grammed. If writing to the watchdog timer control register is not
executed, the watchdog timer does not operate.
When reading the watchdog timer control register is executed, the
contents of the high-order 6-bit counter and the STP instruction bit
(bit 6), and the count source selection bit (bit 7) are read out.
Bit 6 of Watchdog Timer Control Register
When bit 6 of the watchdog timer control register is “0”, the MCU
enters the stop mode by execution of STP instruction.
Just after releasing the stop mode, the watchdog timer restarts
counting (Note). When executing the WIT instruction, the watch-
dog timer does not stop.
When bit 6 is “1”, execution of STP instruction causes an internal
reset. When this bit is set to “1” once, it cannot be rewritten to
“0” by program. Bit 6 is “0” at reset.
The time until the underflow of the watchdog timer register after
writing to the watchdog timer control register is executed is as fol-
lows (when the bit 7 of the watchdog timer control register is “0”) ;
at frequency/2/4/8 mode (f(XIN)) = 8 MHz): 32.768 ms
at low-speed mode (f(XCIN) = 32 KHz): 8.19s
■ Note
The watchdog timer continues to count even during the wait time set
by timer 1 and timer 2 to release the stop state and in the wait
mode. Accordingly, do not underflow the watchdog timer in this time.
Fig. 47 Block diagram of Watchdog timer
Fig. 48 Structure of Watchdog timer control register
Fig. 49 Timing of reset output
Internal reset
signal
Watchdog timer
detection
=32msec (f(XIN)=8MHZ)
f(XIN)
Watchdog timer H (for read-out of high-order 6 bit)
“FF16” is set to watchdog timer by writing to these bits.
Watchdog timer count source selection bit
0: f(XIN)/1024 (f(SUB)/1024 at low-speed mode)
1: f(XIN)/4 (f(SUB)/1024 at low-speed mode)
STP instruction function selection bit
0: Entering stop mode by execution of STP instruction
1: Internal reset by execution of STP instruction
Watchdog timer control register (Address 003716)
WDTCON
b7
b0
Note : Bits 6 and 7 can be rewritten only once after reset.
After rewriting it is disable to write any data to this bit.
XIN
Data bus
XCIN
Internal system clock
selection bit (bit 7 of
the CPU mode register)
1/1024
Watchdog timer
H (6)
Watchdog timer count
source selection bit
Reset
circuit
Undefined instruction
Reset
“FF16” is set when
watchdog timer control
register is written to.
Internal reset
RESET
Wait until reset release
Watchdog timer
L (2)
STP instruction
STP instruction bit
1/4
“0”
“1”
“0”
On-chip oscillator mode
control bit
On-chip oscillator
相關PDF資料
PDF描述
M38259EFDFP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP100
M38254M4-XXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100
M38258MCMXXXHP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100
M38254M6-XXXGP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100
M38257M8-XXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M38258MCM084 制造商:Panasonic Industrial Company 功能描述:IC
M3826 功能描述:電纜固定件和配件 LTRSCG 1000 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M3826 BK001 制造商:Alpha Wire Company 功能描述:CBL 2COND 16AWG BLK 1000'
M3826 BK002 制造商:Alpha Wire Company 功能描述:CBL 2COND 16AWG BLK 500'
M3826 BK005 制造商:Alpha Wire Company 功能描述:CBL 2COND 16AWG BLK 100'
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*