- 您現在的位置：買賣IC網 > PDF目錄45045 > M3826AMFLXXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M3826AMFLXXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 4/80頁 |
| 文件大小： | 1561K |
| 代理商： | M3826AMFLXXXFP |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3826 Group
11
[Processor status register (PS)]
The processor status register is an 8-bit register consisting of 5
flags which indicate the status of the processor after an arithmetic
operation and 3 flags which decide MCU operation. Branch opera-
tions can be performed by testing the Carry (C) flag , Zero (Z) flag,
Overflow (V) flag, or the Negative (N) flag. In decimal mode, the Z,
V, N flags are not valid.
Bit 0: Carry flag (C)
The C flag contains a carry or borrow generated by the arith-
metic logic unit (ALU) immediately after an arithmetic operation.
It can also be changed by a shift or rotate instruction.
Bit 1: Zero flag (Z)
The Z flag is set if the result of an immediate arithmetic operation
or a data transfer is “0”, and cleared if the result is anything other
than “0”.
Bit 2: Interrupt disable flag (I)
The I flag disables all interrupts except for the interrupt gener-
ated by the BRK instruction.
Interrupts are disabled when the I flag is “1”.
Bit 3: Decimal mode flag (D)
The D flag determines whether additions and subtractions are
executed in binary or decimal. Binary arithmetic is executed
when this flag is “0”; decimal arithmetic is executed when it is
“1”.
Decimal correction is automatic in decimal mode. Only the ADC
and SBC instructions can be used for decimal arithmetic.
Bit 4: Break flag (B)
The B flag is used to indicate that the current interrupt was gen-
erated by the BRK instruction. The BRK flag in the processor
status register is always “0”. When the BRK instruction is used to
generate an interrupt, the processor status register is pushed
onto the stack with the break flag set to “1”.
Bit 5: Index X mode flag (T)
When the T flag is “0”, arithmetic operations are performed be-
tween accumulator and memory. When the T flag is “1”, direct
arithmetic operations and direct data transfers are enabled be-
tween memory locations.
Bit 6: Overflow flag (V)
The V flag is used during the addition or subtraction of one byte
of signed data. It is set if the result exceeds +127 to -128. When
the BIT instruction is executed, bit 6 of the memory location op-
erated on by the BIT instruction is stored in the overflow flag.
Bit 7: Negative flag (N)
The N flag is set if the result of an arithmetic operation or data
transfer is negative. When the BIT instruction is executed, bit 7
of the memory location operated on by the BIT instruction is
stored in the negative flag.
Table 6 Set and clear instructions of each bit of processor status register
Set instruction
Clear instruction
C flag
SEC
CLC
Z flag
–
I flag
SEI
CLI
D flag
SED
CLD
B flag
–
T flag
SET
CLT
V flag
–
CLV
N flag
–
相關PDF資料 |
PDF描述 |
|---|---|
| M3826AEFGP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M38268MCLXXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M3826AMFLXXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M3826AMFA-XXXFP | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP100 |
| M3826AMFA-XXXGP | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M3826-BK001 | 制造商:Alpha Wire 功能描述: |
| M3826-BK002 | 制造商:Alpha Wire 功能描述: |
| M3826-BK005 | 制造商:Alpha Wire 功能描述: |
| M3826-BK199 | 制造商:Alpha Wire 功能描述: |
| M3826-BLACK-100 | 制造商:Alpha Wire 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。