- 您現在的位置：買賣IC網 > PDF目錄45045 > M3826AMFLXXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M3826AMFLXXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 40/80頁 |
| 文件大?。?/td> | 1561K |
| 代理商： | M3826AMFLXXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3826 Group
44
Voltage Multiplier (3 Times)
The voltage multiplier performs threefold boosting. This circuit in-
puts a reference voltage for boosting from LCD power input pin
VL1. (However, when using a 1/2 bias, connect VL1 and VL2 and
apply voltage by external resistor division.)
Set each bit of the segment output enable register and the LCD
mode register in the following order for operating the voltage mul-
tiplier.
1. Set the segment output enable bits (bits 0 to 5) of the seg-
ment output enable register to “0” or “1.”
2. Set the duty ratio selection bits (bits 0 and 1), the bias con-
trol bit (bit 2), the LCD circuit divider division ratio selection
bits (bits 5 and 6), and the LCDCK count source selection
bit (bit 7) of the LCD mode register to “0” or “1.”
3. Set the LCD output enable bit (bit 6) of the segment output
enable register to “1.”
4. Set the voltage multiplier control bit (bit 4) of the LCD mode
register to “1.”
When voltage is input to the VL1 pin during operating the voltage
multiplier, voltage that is twice as large as VL1 occurs at the VL2
pin, and voltage that is three times as large as VL1 occurs at the
VL3 pin.
When using the voltage multiplier, apply 1.3 V
≤ Voltage ≤ 2.3 V
(1.3 V
≤ Voltage ≤ 2.1 V for low voltage version) to the VL1 pin.
When not using the voltage multiplier,apply proper voltage to the
LCD power input pins (VL1–VL3). Then set the LCD output enable
bit to “1.”
When the LCD output enable bit is set to “0,” the VCC voltage is
applied to the VL3 pin inside of this microcomputer.
The voltage multiplier control bit (bit 4 of the LCD mode register)
controls the voltage multiplier.
Fig. 44 Example of circuit at each bias
Table 13. Bias control and applied voltage to VL1–VL3
Bias value
1/3 bias
1/2 bias
Voltage value
VL3=VLCD
VL2=2/3 VLCD
VL1=1/3 VLCD
VL3=VLCD
VL2=VL1=1/2 VLCD
Note : VLCD is the maximum value of supplied voltage for the
LCD panel.
Bias Control and Applied Voltage to LCD
Power Input Pins
To the LCD power input pins (VL1–VL3), apply the voltage shown
in Table 13 according to the bias value.
Select a bias value by the bias control bit (bit 2 of the LCD mode
register).
VL3
VL2
C2
C1
VL1
1/3 bias
when using the voltage multiplier
VL3
VL2
C2
C1
VL1
1/3 bias
when not using the voltage multiplier
Open
R2
R1
R3
R1=R2=R3
Contrast control
VL3
VL2
C2
C1
VL1
1/2 bias
Open
R4
R5
R4=R5
Contrast control
PXx
相關PDF資料 |
PDF描述 |
|---|---|
| M3826AEFGP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M38268MCLXXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M3826AMFLXXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M3826AMFA-XXXFP | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP100 |
| M3826AMFA-XXXGP | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M3826-BK001 | 制造商:Alpha Wire 功能描述: |
| M3826-BK002 | 制造商:Alpha Wire 功能描述: |
| M3826-BK005 | 制造商:Alpha Wire 功能描述: |
| M3826-BK199 | 制造商:Alpha Wire 功能描述: |
| M3826-BLACK-100 | 制造商:Alpha Wire 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。