參數資料
型號: M3850
廠商: Mitsubishi Electric Corporation
英文描述: Single Chip 8 Bits Microcomputer(8位單片機)
中文描述: 單芯片8位單片機(8位單片機)
文件頁數: 24/51頁
文件大小: 736K
代理商: M3850
24
3850 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Fig. 21 Operation of UART serial I/O1 function
[Transmit Buffer Register/Receive Buffer
Register (TB/RB)] 0018
16
The transmit buffer register and the receive buffer register are lo-
cated at the same address. The transmit buffer is write-only and
the receive buffer is read-only. If a character bit length is 7 bits, the
MSB of data stored in the receive buffer is “0”.
[Serial I/O1 Status Register (SIOSTS)] 0019
16
The read-only serial I/O1 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O1
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer register is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer reg-
ister, and the receive buffer full flag is set. A write to the serial I/O1
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O1 enable bit SIOE
(bit 7 of the serial I/O1 control register) also clears all the status
flags, including the error flags.
Bits 0 to 6 of the serial I/O1 status register are initialized to “0” at
reset, but if the transmit enable bit (bit 4) of the serial I/O1 control
register has been set to “1”, the transmit shift completion flag (bit
2) and the transmit buffer empty flag (bit 0) become “1”.
[Serial I/O1 Control Register (SIOCON)] 001A
16
The serial I/O1 control register consists of eight control bits for the
serial I/O1 function.
[UART Control Register (UARTCON)] 001B
16
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer and one bit (bit 4) which is al-
ways valid and sets the output structure of the P2
5
/T
X
D pin.
[Baud Rate Generator (BRG)] 001C
16
The baud rate generator determines the baud rate for serial trans-
fer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate genera-
tor.
TSC=0
TBE=1
RBF=0
TBE=0
TBE=0
RBF=1
RBF=1
ST
D
0
D
1
SP
D
0
D
1
ST
SP
TBE=1
TSC=1
ST
D
0
D
1
SP
D
0
D
1
ST
SP
Transmit or receive clock
Transmit buffer write
signal
Generated at 2nd bit in 2-stop-bit mode
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
1:
Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2:
As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit
interrupt source selection bit (TIC) of the serial I/O1 control register.
3:
The receive interrupt (RI) is set when the RBF flag becomes “1.”
4:
After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
Notes
Serial output T
X
D
Serial input R
X
D
Receive buffer read
signal
相關PDF資料
PDF描述
M388504E6FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38867E8A-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38867E8AHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38867E8FS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38867E8AFS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M3850 BK001 制造商:Alpha Wire Company 功能描述:CBL 6COND 14AWG BLK 1000'
M3850 BK002 制造商:Alpha Wire Company 功能描述:CBL 6COND 14AWG BLK 500'
M3850 BK005 制造商:Alpha Wire Company 功能描述:CBL 6COND 14AWG BLK 100'
M3850 BK199 制造商:Alpha Wire Company 功能描述:CBL 6COND 14AWG BLK 3000=3000'
M38500E1H-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 38000 SERIES