參數資料
型號： M38C29MC-XXXFP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64
封裝： 14 X 14 MM, PLASTIC, LQFP-64
文件頁數： 46/101頁
文件大小： 1529K
代理商： M38C29MC-XXXFP
49
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
CLOCK GENERATING CIRCUIT
The 38C2 group has two built-in oscillation circuits; main clock XIN–
XOUT and sub-clock XCIN–XCOUT. An oscillation circuit can be formed
by connecting a resonator between XIN and XOUT (XCIN and XCOUT).
Use the circuit constants in accordance with the resonator
manufacturer’s recommended values. No external resistor is needed
between XIN and XOUT since a feedback resistor exists on-chip. How-
ever, an external feedback resistor is needed between XCIN and
XCOUT.
When the clock signal is supplied from external for the main clock,
input the signal to XIN pin and connect XOUT pin to VCC through 1 k
resistor.
When the clock signal is supplied from external for the sub-clock,
input the signal to XCIN and leave XCOUT open.
Immediately after power on, only the XIN oscillation circuit starts os-
cillating.
Frequency Control
(1) Frequency/8 Mode
The system clock
φ is the frequency of XIN divided by 8. After reset is
released, this mode is selected.
(2) Frequency/4 Mode
The system clock
φ is the frequency of XIN divided by 4.
(3) Frequency/2 Mode
The system clock
φ is the frequency of XIN divided by 2.
(4) Low-speed Mode
The system clock
φ is the frequency of XCIN divided by 2. In the low-
speed mode, the low-power dissipation operation can be performed
when the main clock XIN is stopped by setting the bit 7 of the CPU
mode register to “0”. In this case, when main clock XIN oscillation is
restarted, generate the wait time until the oscillation is stable by pro-
gram after the bit 7 of the CPU mode register is set to “1”.
Fig. 50 Ceramic resonator circuit
Fig. 51 External clock input circuit
XOUT
CIN
COUT
CCIN
CCOUT
Rfc
XCIN
XCOUT
XIN
s Notes on Clock Generating Circuit
If you switch the mode between frequency/2/4, or 8 and low-speed,
stabilize both XIN and XCIN oscillations. The sufficient time is required
for the sub-clock to stabilize, especially immediately after power on
and at returning from stop mode. When switching the mode, set the
frequency on condition that f(XIN) > 3f(XCIN).
Oscillation Control
(1) Stop Mode
If the STP instruction is executed, the system clock
φ stops at an “H”
level, and main clock and sub-clock oscillators stop.
In this time, values set previously to timer 1 latch and timer 2 latch
are loaded automatically to timer 1 and timer 2. Set the values to
generate the wait time required for oscillation stabilization to timer 1
latch and timer 2 latch (low-order 8 bits of timer 1 and high-order 8
bits of timer 2) before the STP instruction.
The frequency divider for timer 1 is used for the timer 1 count source,
and the output of timer 1 is forcibly connected to timer 2. In this time,
bits 0 to 5 of the timer 12 mode register are cleared to “0”.
The values of the timer 12 frequency divider selection register are
not changed.
Set the interrupt enable bits of the timer 1 and timer 2 to disabled
(“0”) before executing the STP instruction.
Oscillator restarts When reset occurs or an interrupt request is re-
ceived, but the system clock
φ is not supplied to the CPU until timer
2 underflows. This allows time for the clock circuit oscillation to stabi-
lize.
(2) Wait Mode
If the WIT instruction is executed, the system clock
φ stops at an “H”
level. The states of XIN and XCIN are the same as the state before
executing the WIT instruction. The system clock
φ restarts at reset or
when an interrupt is received. Since the oscillator does not stop, nor-
mal operation can be started immediately after the clock is restarted.
XCIN
XCOUT
XIN
XOUT
External oscillation circuit
VCC
VSS
Open
VCC
VSS
External oscillation
circuit, or External pulse
1 k
VCC
相關PDF資料
PDF描述
M38C29FFFP 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP64
M38C29FFHP 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP64
M38C34M6AXXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80
M38C37ECMFS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC80
M38C37ECAFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
M38C29MC-XXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29RLFS 功能描述:EMULATOR MCU FOR A-VERSION 38C2 RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
M38C29T-64FPD 功能描述:DEV 100-PIN RFS/MCU TO 64-PIN 0. RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF)
M38C29T-64LCA 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter from 100-pin RFS Type Emulator MCU to 64-pin 0.8mm-pitch QFP (for 38C1, 38C2, 38K0 and 38K2 Group of 38000 Series)
M38C29T-ADF 功能描述:DEV TEMPORARY TARGET BOARD FOR M RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*