參數資料
型號： M38C29MC-XXXFP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64
封裝： 14 X 14 MM, PLASTIC, LQFP-64
文件頁數： 51/101頁
文件大?。?/td> 1529K
代理商： M38C29MC-XXXFP
53
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is “1.” After a
reset, initialize flags which affect program execution. In particular, it
is essential to initialize the index X mode (T) and the decimal mode
(D) flags because of their effect on calculations.
Interrupts
The contents of the interrupt request bits do not change immediately
after they have been written. After writing to an interrupt request reg-
ister, execute at least one instruction before performing a BBC or
BBS instruction.
Decimal Calculations
To calculate in decimal notation, set the decimal mode flag (D) to
“1,” then execute an ADC or SBC instruction. After executing an
ADC or SBC instruction, execute at least one instruction before
executing an SEC, CLC, or CLD instruction.
In decimal mode, the values of the negative (N), overflow (V), and
zero (Z) flags are invalid.
Timers
If a value n (between 0 and 255) is written to a timer latch, the
frequency division ratio is 1/(n+1).
The timers share the one frequency divider to generate the count
source. Accordingly, when each timer starts operating, initializing
the frequency divider is not executed. Therefore, when the frequency
divider is selected for the count source, the delay of the maximum
one cycle of the count source is generated until the timer starts
counting or the waveform is output from timer starts operating. Also,
the count source cannot be checked externally.
Multiplication and Division Instructions
The index X mode (T) and the decimal mode (D) flags do not affect
the MUL and DIV instruction.
The execution of these instructions does not change the contents
of the processor status register.
Ports
The contents of the port direction registers cannot be read. The fol-
lowing cannot be used:
The data transfer instruction (LDA, etc.)
The operation instruction when the index X mode flag (T) is “1”
The addressing mode which uses the value of a direction register
as an index
The bit-test instruction (BBC or BBS, etc.) to a direction register
The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a
direction register.
Use instructions such as LDM and STA, etc., to set the port direction
registers.
Serial I/O
In clock synchronous serial I/O, if the receive side is using an exter-
nal clock and it is to output the SRDY signal, set the transmit enable
bit, the receive enable bit, and the SRDY output enable bit to “1.”
Serial I/O continues to output the final bit from the TXD pin after trans-
mission is completed.
A-D Converter
The comparator uses internal capacitors whose charge will be lost if
the clock frequency is too low.
Therefore, set the A-D clock frequency to 250 kHz or more.
Also, when the STP instruction is executed during the A-D conver-
sion, the A-D conversion is stopped immediately, the A-D conversion
completion bit is set to “1”, and the interrupt request is generated.
Instruction Execution Time
The instruction execution time is obtained by multiplying the number
of cycles shown in the list of machine instructions by the period of the
internal clock
φ.
相關PDF資料
PDF描述
M38C29FFFP 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP64
M38C29FFHP 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP64
M38C34M6AXXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80
M38C37ECMFS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC80
M38C37ECAFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
M38C29MC-XXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29RLFS 功能描述:EMULATOR MCU FOR A-VERSION 38C2 RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
M38C29T-64FPD 功能描述:DEV 100-PIN RFS/MCU TO 64-PIN 0. RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF)
M38C29T-64LCA 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter from 100-pin RFS Type Emulator MCU to 64-pin 0.8mm-pitch QFP (for 38C1, 38C2, 38K0 and 38K2 Group of 38000 Series)
M38C29T-ADF 功能描述:DEV TEMPORARY TARGET BOARD FOR M RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*