參數資料
型號： M38D24G4HP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
封裝： 10X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64
文件頁數： 127/136頁
文件大小： 2856K
代理商： M38D24G4HP
Rev.3.02
Apr 10, 2008
Page 90 of 131
REJ03B0177-0302
38D2 Group
NOTES ON QzROM VERSION
Wiring to OSCSEL pin
1. OSCSEL = L
Connect the OSCSEL pin the shortest possible to the GND
pattern which is supplied to the VSS pin of the microcomputer.
In addition connecting an approximately 5 k
Ω resistor in series
to the GND could improve noise immunity. In this case as well
as the above mention, connect the pin the shortest possible to
the GND pattern which is supplied to the VSS pin of the
microcomputer.
2. OSCSEL = H
Connect the OSCSEL pin the shortest possible to the VCC
pattern which is supplied to the VCC pin of the microcomputer.
In addition connecting an approximately 5 k
Ω resistor in series
to the VCC could improve noise immunity. In this case as well
as the above mention, connect the pin the shortest possible to
the VCC pattern which is supplied to the VCC pin of the
microcomputer.
Reason
The OSCSEL pin is the power source input pin for the built-in
QzROM.
When programming in the QzROM, the impedance of the
OSCSEL pin is low to allow the electric current for writing to
flow into the built-in QzROM. Because of this, noise can enter
easily. If noise enters the OSCSEL pin, abnormal instruction
codes or data are read from the QzROM, which may cause a
program runaway.
Fig. 86 Wiring for the OSCSEL pin
Precautions Regarding Overvoltage in QzROM Version
Make sure that voltage exceeding the VCC pin voltage is not
applied to other pins. In particular, ensure that the state indicated
by bold lines in figure below does not occur for OSCSEL pin
(VPP power source pin for QzROM) during power-on or power-
off. Otherwise the contents of QzROM could be rewritten.
Fig. 87 Example of Overvoltage
Product shipped in blank
As for the product shipped in blank, Renesas does not perform
the writing test to user ROM area after the assembly process
though the QzROM writing test is performed enough before the
assembly process. Therefore, a writing error of approximate
0.1% may occur.
Moreover, please note the contact of cables and foreign bodies on
a socket, etc. because a writing environment may cause some
writing errors.
Notes On QzROM Writing Orders
When ordering the QzROM product shipped after writing,
submit the mask file (extension: .msk) which is made by the
mask file converter MM.
Be sure to set the ROM option data* setup when making the
mask file by using the mask file converter MM.. The ROM
code protect is specified according to the ROM option data* in
the mask file which is submitted at ordering. Note that the
mask file which has nothing at the ROM option data* or has
the data other than “0016”, “FE16” and “FF16” can not be
accepted.
Set “FF16” to the ROM code protect address in ROM data
regardless of the presence or absence of a protect. When data
other than “FF16” is set, we may ask that the ROM data be
submitted again.
* ROM option data: mask option noted in MM
Data Required For QzROM Writing Orders
The following are necessary when ordering a QzROM product
shipped after writing:
1. QzROM Writing Confirmation Form*
2. Mark Specification Form*
3. ROM data...........Mask file
* For the QzROM writing confirmation form and the mark
specification form, refer to the “Renesas Technology Corp.”
Homepage (http://www.renesas.com/homepage.jsp).
Note that we cannot deal with special font marking (customer's
trademark etc.) in QzROM microcomputer.
QzROM Receive Flow
When writing to QzROM is performed by user side, the
receiving inspection by the following flow is necessary.
Fig. 88 QzROM receive flow
OSCSEL
VSS
The shortest
about 5 k
Ω
Termination of OSCSEL pin
OSCSEL
VCC
The shortest
about 5 k
Ω
(1) OSCSEL = L
(2) OSCSEL = H
(1)
Note 1: It shows the microcomputer’s pin
VCC pin voltage
OSCSEL pin voltage
“H” input
OSCSEL pin voltage
“L” input
1.8V
(1) Input voltage to other MCU pins rises before VCC pin voltage.
(2) Input voltage to other MCU pins falls after VCC pin voltage.
Note: The internal circuitry is unstable when VCC is below the minimum voltage
specification of 1.8 V (shaded portion), so particular care should be
exercised regarding overvoltage.
(1)
(2)
QzROM product shipped in blank
Programming
Verify test
Receiving inspection of
unprotected area (Verify test)
Programming to unprotected area
Verify test for unprotected area
Shipping
User
QzROM product shipped after writing
“protect disabled”
“protect enabled to the protect area 1”
Renesas
Receiving inspection
(Blank check)
Programming
Verify test for all area
Shipping
User
Renesas
相關PDF資料
PDF描述
M38D24G6FP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
M38D24G4FP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
M38D59FFHP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP80
M38D58G8HP 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PQFP80
M38D59GFFP 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
M38D24G4HP#U0 功能描述:IC 740/38D2 MCU QZ-ROM 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR)
M38D24G4XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D24G4XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D24G5XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D24G5XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*