參數資料
型號: M38D24G6FP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
封裝: 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64
文件頁數: 63/138頁
文件大小: 2880K
代理商: M38D24G6FP
Rev.3.02
Apr 10, 2008
Page 28 of 131
REJ03B0177-0302
38D2 Group
<Notes>
The interrupt request bit may be set to “1” in the following cases.
When setting the external interrupt active edge
Related bits: INT0 interrupt edge selection bit
(bit 0 of interrupt edge selection register
(address 003A16))
INT1 interrupt edge selection bit
(bit 1 of interrupt edge selection register)
INT2 interrupt edge selection bit
(bit 2 of interrupt edge selection register)
CNTR0 activate edge switch bit
(bits 6 and 7 of timer X control register 1
(address 002E16))
CNTR1 activate edge switch bit
(bits 6 of timer Y mode register
(address 003816))
When switching the interrupt sources of an interrupt vector
address where two or more interrupt sources are assigned
Related bit:
Timer Y/CNTR1 interrupt switch bit
(bit 3 of interrupt edge selection register)
If it is not necessary to generate an interrupt synchronized with
these settings, take the following sequence.
(1) Set the corresponding enable bit to “0” (disabled).
(2) Set the interrupt edge selection bit (the active edge switch
bit) or the interrupt source bit.
(3) Set the corresponding interrupt request bit to “0” after one
or more instructions have been executed.
(4) Set the corresponding interrupt enable bit to “1” (enabled).
Fig. 20 Timing of interrupt request generation, interrupt request bit, and interrupt acceptance
T1
(1) The interrupt request bit for an interrupt request generated during period 1 is set to “1” at timing point IR1.
(2) The interrupt request bit for an interrupt request generated during period 2 is set to “1” at timing point IR1 or IR2.
The timing point at which the bit is set to “1” varies depending on conditions. When two or more interrupt
requests are generated during the period 2, each request bit may be set to “1” at timing point IR1 or IR2
separately.
T1 T2 T3 : Interrupt acceptance timing points
IR1 IR2 : Timings points at which the interrupt request bit is set to “1”.
Note : Period 2 indicates the last
φ cycle during one instruction cycle.
IR1T2
SYNC
IR2 T3
12
Internal clock
φ
Instruction cycle
Push onto stack
Vector fetch
Instruction cycle
相關PDF資料
PDF描述
M38D29GC-XXXFP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
M38D24G4HP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
M38D29GC-XXXHP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
M38D24G4-XXXFP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
M38D29GF-XXXHP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
M38D24G6FP#U0 功能描述:IC 740/38D2 MCU QZ-ROM 80QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI,I²C,UART/USART 外圍設備:POR,PWM,WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC(J 形引線) 包裝:帶卷 (TR)
M38D24G6HP#U0 功能描述:IC 740/38D2 MCU QZ-ROM 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI,I²C,UART/USART 外圍設備:POR,PWM,WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC(J 形引線) 包裝:帶卷 (TR)
M38D24G6XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D24G6XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D24G7XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER