- 您現在的位置：買賣IC網 > PDF目錄377826 > M41T00S (意法半導體) Serial Access Real-Time Clock(串行存取實時時鐘) PDF資料下載
參數資料
| 型號： | M41T00S |
| 廠商： | 意法半導體 |
| 英文描述： | Serial Access Real-Time Clock(串行存取實時時鐘) |
| 中文描述： | 串行訪問實時時鐘（串行存取實時時鐘） |
| 文件頁數： | 12/23頁 |
| 文件大?。?/td> | 319K |
| 代理商： | M41T00S |
M41T00S
12/23
Calibrating the Clock
The M41T00S is driven by a quartz-controlled os-
cillator with a nominal frequency of 32,768 Hz. The
devices are tested not exceed ±35 ppm (parts per
million) oscillator frequency error at 25
o
C, which
equates to about ±1.53 minutes per month (see
Figure 11., page 13
). When the Calibration circuit
is properly employed, accuracy improves to better
than ±2 ppm at 25°C.
The oscillation rate of crystals changes with tem-
perature. The M41T00S design employs periodic
counter correction. The calibration circuit adds or
subtracts counts from the oscillator divider circuit
at the divide by 256 stage, as shown in
Figure
12., page 13
. The number of times pulses which
are blanked (subtracted, negative calibration) or
split (added, positive calibration) depends upon
the value loaded into the five Calibration Bits found
in the Calibration Register. Adding counts speeds
the clock up, subtracting counts slows the clock
down.
The Calibration Bits occupy the five lower order
bits (D4-D0) in the Calibration Register 07h. These
bits can be set to represent any value between 0
and 31 in binary form. Bit D5 is a Sign Bit; '1' indi-
cates positive calibration, '0' indicates negative
calibration. Calibration occurs within a 64 minute
cycle. The first 62 minutes in the cycle may, once
per minute, have one second either shortened by
128 or lengthened by 256 oscillator cycles. If a bi-
nary '1' is loaded into the register, only the first 2
minutes in the 64 minute cycle will be modified; if
a binary 6 is loaded, the first 12 will be affected,
and so on.
Therefore, each calibration step has the effect of
adding 512 or subtracting 256 oscillator cycles for
every 125,829,120 actual oscillator cycles, that is
+4.068 or –2.034 ppm of adjustment per calibra-
tion step in the calibration register (see
Figure
12., page 13
). Assuming that the oscillator is run-
ning at exactly 32,768 Hz, each of the 31 incre-
ments in the Calibration byte would represent
+10.7 or –5.35 seconds per month which corre-
sponds to a total range of +5.5 or –2.75 minutes
per month.
Two methods are available for ascertaining how
much calibration a given M41T00S may require.
The first involves setting the clock, letting it run for
a month and comparing it to a known accurate ref-
erence and recording deviation over a fixed period
of time. Calibration values, including the number of
seconds lost or gained in a given period, can be
found in Application Note AN934, “TIMEKEEP-
ER
CALIBRATION.” This allows the designer to
give the end user the ability to calibrate the clock
as the environment requires, even if the final prod-
uct is packaged in a non-user serviceable enclo-
sure. The designer could provide a simple utility
that accesses the Calibration byte.
The second approach is better suited to a manu-
facturing environment, and involves the use of the
FT/OUT pin. The pin will toggle at 512Hz, when
the Stop Bit (ST, D7 of 00h) is '0,' and the Frequen-
cy Test Bit (FT, D6 of 07h) is '1.'
Any deviation from 512 Hz indicates the degree
and direction of oscillator frequency shift at the test
temperature.
For
example,
512.010124 Hz would indicate a +20 ppm oscilla-
tor frequency error, requiring a –10 (XX001010) to
be loaded into the Calibration Byte for correction.
Note that setting or changing the Calibration Byte
does not affect the Frequency Test output fre-
quency.
The FT/OUT pin is an open drain output which re-
quires a pull-up resistor to V
CC
for proper opera-
tion. A 500-10k resistor is recommended in order
to control the rise time. The FT Bit is cleared on
power-down.
a
reading
of
相關PDF資料 |
PDF描述 |
|---|---|
| M41T0 | Serial Real-Time Clock(串行實時時鐘) |
| M41T11M6E | Serial Real Time Clock with 56 Bytes of NVRAM |
| M41T11M6F | Serial Real Time Clock with 56 Bytes of NVRAM |
| M41T11MH6E | Serial Real Time Clock with 56 Bytes of NVRAM |
| M41T11MH6F | Serial Real Time Clock with 56 Bytes of NVRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M41T00S_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial access real-time clock |
| M41T00SC64 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Real-Time Clock + 64Kbit (8192 x 8) EEPROM |
| M41T00SC64MY6E | 功能描述:電可擦除可編程只讀存儲器 SERIAL REAL TIME CLOCK 64Kb 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M41T00SC64MY6F | 功能描述:電可擦除可編程只讀存儲器 64 Kbit 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M41T00SM6E | 功能描述:實時時鐘 2.0 to 5.5V 64 (8X8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。