- 您現在的位置：買賣IC網 > PDF目錄359071 > M50FW002K5T (意法半導體) 2 Mbit 256Kb x8, Boot Block 3V Supply Firmware Hub Flash Memory PDF資料下載
參數資料
| 型號： | M50FW002K5T |
| 廠商： | 意法半導體 |
| 英文描述： | 2 Mbit 256Kb x8, Boot Block 3V Supply Firmware Hub Flash Memory |
| 中文描述： | 2兆位的256Kb × 8，啟動塊3V電源閃存固件集線器 |
| 文件頁數： | 11/39頁 |
| 文件大?。?/td> | 254K |
| 代理商： | M50FW002K5T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
11/39
M50FW002
Address/Address Multiplexed (A/A Mux) Bus
Operations
The Address/Address Multiplexed (A/A Mux)
Interface has a more traditional style interface.
The signals consist of a multiplexed address
signals (A0-A10), data signals, (DQ0-DQ7) and
three control signals (RC, G, W). An additional
signal, RP, can be used to reset the memory.
The Address/Address Multiplexed (A/A Mux)
Interface
is
included
Programming equipment
programming. Only a subset of the features
available to the Firmware Hub (FWH) Interface are
available; these include all the Commands but
exclude the Security features and other registers.
The following operations can be performed using
the appropriate bus cycles: Bus Read, Bus Write,
Output Disable and Reset.
When the Address/Address Multiplexed (A/A Mux)
Interface is
selected all the blocks
unprotected. It is not possible to protect any blocks
through this interface.
Bus Read.
Bus Read operations are used to
output the contents of the Memory Array, the
Electronic Signature and the Status Register. A
valid Bus Read operation begins by latching the
Row Address and Column Address signals into
the memory using the Address Inputs, A0-A10,
and the Row/Column Address Select RC. Then
Write Enable (W) and Interface Reset (RP) must
be High, V
IH
, and Output Enable, G, Low, V
IL
, in
for
use
faster factory
by
Flash
for
are
order to perform a Bus Read operation. The Data
Inputs/Outputs will output the value, see Figure
12, Read AC Waveforms (A/A Mux Interface), and
Table 24, A/A Mux Interface Read AC
Characteristics, for details of when the output
becomes valid.
Bus Write.
Bus Write operations write to the
Command Interface. A valid Bus Write operation
begins by latching the Row Address and Column
Address signals into the memory using the
Address Inputs, A0-A10, and the Row/Column
Address Select RC. The data should be set up on
the Data Inputs/Outputs; Output Enable, G, and
Interface Reset, RP, must be High, V
IH
and Write
Enable, W, must be Low, V
IL
. The Data Inputs/
Outputs are latched on the rising edge of Write
Enable, W. See Figure 13, and Table 25, A/A Mux
Interface Write AC Characteristics, for details of
the timing requirements.
Output Disable.
The data outputs are high-im-
pedance when the Output Enable, G, is at V
IH
.
Reset.
During Reset mode all internal circuits are
switched off, the memory is deselected and the
outputs are put in high-impedance. The memory is
in Reset mode when RP is Low, V
IL
. RP must be
held Low, V
IL
for t
PLPH
. If RP is goes Low, V
IL
,
during a Program or Erase operation, the
operation is aborted and the memory cells affected
no longer contain valid data; the memory can take
up to t
PLRH
to abort a Program or Erase operation.
Table 6. A/A Mux Bus Operations
Table 7. Manufacturer and Device Codes
Operation
G
W
RP
V
PP
DQ7-DQ0
Bus Read
V
IL
V
IH
V
IH
Don’t Care
Data Output
Bus Write
V
IH
V
IL
V
IH
V
CC
or V
PPH
Data Input
Output Disable
V
IH
V
IH
V
IH
Don’t Care
Hi-Z
Reset
V
IL
or V
IH
V
IL
or V
IH
V
IL
Don’t Care
Hi-Z
Operation
G
W
RP
A17-A1
A0
DQ7-DQ0
Manufacturer Code
V
IL
V
IH
V
IH
V
IL
V
IL
20h
Device Code
V
IL
V
IH
V
IH
V
IL
V
IH
29h
相關PDF資料 |
PDF描述 |
|---|---|
| M50FW002K1T | 2 Mbit 256Kb x8, Boot Block 3V Supply Firmware Hub Flash Memory |
| M50FW002K | 2 Mbit 256Kb x8, Boot Block 3V Supply Firmware Hub Flash Memory |
| M50FW002 | 2 Mbit 256Kb x8, Boot Block 3V Supply Firmware Hub Flash Memory |
| M50LPW041K1T | 4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory |
| M50LPW041N1T | 4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FW016 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW016N | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW016N1 | 功能描述:閃存 3.0-3.6V 16M (2Mx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FW016N1G | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW016N1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。