- 您現在的位置：買賣IC網 > PDF目錄377830 > M50FW080N5TP (意法半導體) 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory PDF資料下載
參數資料
| 型號： | M50FW080N5TP |
| 廠商： | 意法半導體 |
| 英文描述： | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| 中文描述： | 8兆1兆× 8，統一座3V電源閃存固件集線器 |
| 文件頁數： | 23/56頁 |
| 文件大?。?/td> | 292K |
| 代理商： | M50FW080N5TP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
M50FW080
Command interface
23/55
4
Command interface
All Bus Write operations to the memory are interpreted by the Command Interface.
Commands consist of one or more sequential Bus Write operations.
After power-up or a Reset operation the memory enters Read mode.
The commands are summarized in
Table 9
, Commands. The following text descriptions
should be read in conjunction with
Table 9
.
4.1
Read Memory Array command
The Read Memory Array command returns the memory to its Read mode where it behaves
like a ROM or EPROM. One Bus Write cycle is required to issue the Read Memory Array
command and return the memory to Read mode. Once the command is issued the memory
remains in Read mode until another command is issued. From Read mode Bus Read
operations will access the memory array.
While the Program/Erase Controller is executing a Program or Erase operation the memory
will not accept the Read Memory Array command until the operation completes.
4.2
Read Status Register command
The Read Status Register command is used to read the Status Register. One Bus Write
cycle is required to issue the Read Status Register command. Once the command is issued
subsequent Bus Read operations read the Status Register until another command is issued.
See the section on the Status Register for details on the definitions of the Status Register
bits.
4.3
Read Electronic Signature command
The Read Electronic Signature command is used to read the Manufacturer Code and the
Device Code. One Bus Write cycle is required to issue the Read Electronic Signature
command. Once the command is issued subsequent Bus Read operations read the
Manufacturer Code or the Device Code until another command is issued.
After the Read Electronic Signature Command is issued the Manufacturer Code and Device
Code can be read using Bus Read operations using the addresses in
Table 8
.
Table 8.
Read Electronic Signature
Code
Address
Data
Manufacturer Code
00000h
20h
Device Code
00001h
2Dh
相關PDF資料 |
PDF描述 |
|---|---|
| M50FW080NB5P | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB5TP | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50LPW002 | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW002K | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW002K1T | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FW080NB1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB1G | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB1TG | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB5 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。