- 您現在的位置：買賣IC網 > PDF目錄377830 > M50LPW012K (意法半導體) 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory PDF資料下載
參數資料
| 型號： | M50LPW012K |
| 廠商： | 意法半導體 |
| 英文描述： | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| 中文描述： | 2兆位的256Kb × 8，啟動塊3V電源低引腳數快閃記憶體 |
| 文件頁數： | 14/35頁 |
| 文件大?。?/td> | 239K |
| 代理商： | M50LPW012K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
M50LPW012
14/35
Table 14. Status Register Bits
Note: 1.
For Program operations during Erase Suspend Bit 6 is ‘1’, otherwise Bit 6 is ‘0’.
Operation
Bit 7
Bit 6
Bit 5
Bit 4
Bit 2
Bit 1
Program active
0
X
(1)
0
0
0
0
Program suspended
1
X
(1)
0
0
1
0
Program completed successfully
1
X
(1)
0
0
0
0
Program failure due to Block Protection (LPC Interface only)
1
X
(1)
0
0
0
1
Program failure due to cell failure
1
X
(1)
0
1
0
0
Erase active
0
0
0
0
0
0
Block Erase suspended
1
1
0
0
0
0
Erase completed successfully
1
0
0
0
0
0
Block Erase failure due to Block Protection (LPC Interface only)
1
0
0
0
0
1
Erase failure due to failed cell(s)
1
0
1
0
0
0
After the Program/Erase Controller completes its
operation the Erase Status, Program Status and
Block Protection Status bits should be tested for
errors.
Erase Suspend Status (Bit 6).
The Erase Sus-
pend Status bit indicates that a Block Erase oper-
ation has been suspended and is waiting to be
resumed. The Erase Suspend Status should only
be considered valid when the Program/Erase
Controller Status bit is ‘1’ (Program/Erase Control-
ler inactive); after a Program/Erase Suspend com-
mand is issued the memory may still complete the
operation rather than entering the Suspend mode.
When the Erase Suspend Status bit is ‘0’ the Pro-
gram/Erase Controller is active or has completed
its operation; when the bit is ‘1’ a Program/Erase
Suspend command has been issued and the
memory is waiting for a Program/Erase Resume
command.
When a Program/Erase Resume command is is-
sued the Erase Suspend Status bit returns to ‘0’.
Erase Status (Bit 5).
The Erase Status bit can be
used to identify if the memory has applied the
maximum number of erase pulses to the block(s)
and still failed to verify that the block(s) has erased
correctly. The Erase Status bit should be read
once the Program/Erase Controller Status bit is ‘1’
(Program/Erase Controller inactive).
When the Erase Status bit is ‘0’ the memory has
successfully verified that the block(s) has erased
correctly; when the Erase Status bit is ‘1’ the Pro-
gram/Erase Controller has applied the maximum
number of pulses to the block(s) and still failed to
verify that the block(s) has erased correctly.
Once the Erase Status bit is set to ‘1’ it can only be
reset to ‘0’ by a Clear Status Register command or
a hardware reset. If it is set to ‘1’ it should be reset
before a new Program or Erase command is is-
sued, otherwise the new command will appear to
fail.
Program Status (Bit 4).
The Program Status bit
can be used to identify if the memory has applied
the maximum number of program pulses to the
Byte and still failed to verify that the Byte has pro-
grammed correctly. The Program Status bit should
be read once the Program/Erase Controller Status
bit is ‘1’ (Program/Erase Controller inactive).
When the Program Status bit is ‘0’ the memory has
successfully verified that the Byte has pro-
grammed correctly; when the Program Status bit is
‘1’ the Program/Erase Controller has applied the
maximum number of pulses to the Byte and still
failed to verify that the Byte has programmed cor-
rectly.
Once the Program Status bit is set to ‘1’ it can only
be reset to ‘0’ by a Clear Status Register com-
mand or a hardware reset. If it is set to ‘1’ it should
be reset before a new Program or Erase command
is issued, otherwise the new command will appear
to fail.
Reserved (Bit 3).
This status bit is reserved for
future use. Its value should be masked out when-
ever the status register is read.
Program Suspend Status (Bit 2).
The Program
Suspend Status bit indicates that a Program oper-
ation has been suspended and is waiting to be re-
sumed. The Program Suspend Status should only
be considered valid when the Program/Erase
Controller Status bit is ‘1’ (Program/Erase Control-
ler inactive); after a Program/Erase Suspend com-
mand is issued the memory may still complete the
operation rather than entering the Suspend mode.
相關PDF資料 |
PDF描述 |
|---|---|
| M50LPW012K1T | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW040 | 4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory |
| M50LPW040K | 4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory |
| M50LPW040K1T | 4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory |
| M50LPW040K5T | 4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50LPW012K1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW040 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory |
| M50LPW040K | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory |
| M50LPW040K1 | 功能描述:閃存 3.6V 4M (512Kx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50LPW040K1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。