- 您現在的位置：買賣IC網 > PDF目錄384639 > M54676P (Mitsubishi Electric Corporation) 2-PHASE STEPPER MOTOR DRIVER PDF資料下載
參數資料
| 型號： | M54676P |
| 廠商： | Mitsubishi Electric Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 2-PHASE STEPPER MOTOR DRIVER |
| 中文描述： | 二相步進電機驅動器 |
| 文件頁數： | 3/5頁 |
| 文件大?。?/td> | 112K |
| 代理商： | M54676P |
2-PHASE STEPPER MOTOR DRIVER
M54676P
MITSUBISHI <CONTROL / DRIVER IC>
FUNCTION DESCRIPTION
Phase input
Phase input decides the output mode.
*
Z: High impedance
In order to prevent through current caused by turning on output
transistors simultaneously at PhaseA=Phase
A=“H”, both phase
inputs go in the high mode simultaneously and output goes in the
high impedance state.
Furthermore, as a countermeasure against output through current
at the time of phase switching, a delay time (3us) to turn on the
motor drive output when phase input goes in high state is set
within the IC.
Vref input (Comparative voltage)
Chopper current (motor current) is controlled by changing Vref
input voltage.
By inputting SIN wave to VrefA and COS wave to VrefB, A-phase
coil current and B-phase coil current change continuously and the
microstep drive of a stepper motor is performed.
Current comparator
Sense pin voltage (voltage fall at current sensing resistor = motor
current) and Vref input proportional voltage (Vref/10) are
compared.
Sense pin voltage < Vref/10: the comparator output is in high
state and output transistors are turned on. Then, current flows into
the motor.
Sense pin voltage > Vref/10: the comparator output is in low state
and output transistors are turned off. Current does not flow into
the motor.
The above operation is repeated to control the current of the
motor.
Vref comparator
Vref input proportional voltage {(Vref/10)} and internal reference
voltage are compared. If Vref input voltage is 0.3V or lower,
output transistors are turned off and motor current stops
regardless of Phase input and Sense input.
Standby circuit
When Vcc5 voltage is 0.8V or below or open, the IC goes in the
standby state. In the standby state, leak current does not flow into
VM power supply, logic input pins (Phase input), and analog input
pins (Vref input and Sense input). Never forget to set VM power
supply to be the maximum voltage level among all voltages
applied to the IC in the standby state. (As for details, refer to
“PRECAUTIONS FOR USE.”)
Thermal shutdown (TSD) circuit
This IC has the thermal shutdown function to protect itself against
damage by a fire when chip temperature rises abnormally.
Flywheel diode
Because flywheel diodes for chopper current control are built in
this IC, it is not necessary to connect external flywheel diodes.
Also, by connecting schottky diodes with low VF externally, it is
possible to reduce thermal loss.
PhaseA
(PhaseB)
H
L
L
H
H
H
L
L
H
L
L
H
Z
Z
Z
Z
Phase
A
(Phase
B)
OutA
(OutB)
Out
A
(Out
B)
相關PDF資料 |
PDF描述 |
|---|---|
| M54995 | nullBi-CMOS 8-BIT SERIAL-INPUT LATCHED DRIVER |
| M54995FP | nullBi-CMOS 8-BIT SERIAL-INPUT LATCHED DRIVER |
| M54995P | nullBi-CMOS 8-BIT SERIAL-INPUT LATCHED DRIVER |
| M57915L | HYBRID IC FOR DRIVING TRANSISTOR MODULES |
| M57916L | HYBRID IC FOR DRIVING TRANSISTOR MODULES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M54677FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:2-PHASE STEPPER MOTOR DRIVER |
| M54678FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:2-PHASE STEPPER MOTOR DRIVER |
| M54679FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:2-PHASE STEPPER MOTOR DRIVER |
| M54679SP | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:2-Phase Stepper Motor Driver |
| M54679SP(#TB0G) | 制造商:Renesas Electronics Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。