- 您現在的位置：買賣IC網 > PDF目錄370992 > M66515 (Mitsubishi Electric Corporation) LASER-DIODE DRIVER/CONTROLLER PDF資料下載
參數資料
| 型號： | M66515 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | LASER-DIODE DRIVER/CONTROLLER |
| 中文描述： | 激光二極管驅動器/控制器 |
| 文件頁數： | 3/7頁 |
| 文件大?。?/td> | 174K |
| 代理商： | M66515 |
3
MITSUBISHI
DIGITAL ASSP
M66515FP
LASER-DIODE DRIVER/CONTROLLER
OPERATION
1. Laser Drive Currents
The approximate values of laser drive currents, I
SW
and I
B
,
are obtained by the following equation, in which V
C
is the volt-
age of holding capacitor connected to the C
H
pin.
(1) I
SW
(switching current)
V
C
[V]
R
S
[k
]
I
SW
[mA] = 12
×
provided that 0
≤
V
C
≤
V
CC
– 1.8V and I
SW (max.)
=120mA
where R
S
is the resistance of the resistor connected between
the R
S
pin and GND.
(2) I
B
(bias current)
V
B
[V]
R
B
[k
]
I
B
[mA] = 10
×
provided that 0
≤
V
B
≤
Vcc – 2.7V and I
B (max.)
= 30mA
where R
B
is the resistance of the resistor connected between
the R
B
pin and GND.
2. Switching Operation
If DATA = “L,” the LD drive current is I
SW
+ I
B
; if DATA = “H,”
I
B
.
3. ENB Input
When the laser drive current is controlled by the DATA input,
the M66515’s internal current source is maintained turned on.
In contrast, the control by ENB is turning on and off at the cur-
rent source. If ENB = “L” the current source turns on; if ENB =
“H” off.
When ENB = “H” the C
H
pin is compulsorily fixed to “L” in or-
der to discharge the capacitor connected to the C
H
pin.
4. Internal Reset Function
The M66515 has a reset circuit built in for the protection of
laser from an excessive current flowing at the moment of
power on. The internal current source goes off in the range
Vcc < 3.5V (typ.), and the C
H
pin is compulsorily fixed to “L” at
the same time.
5. RO Pin
A load resistor for laser drive current is connected to the RO
pin, through which a current almost equal to I
SW
flows in
(when DATA = “H”). The load resistor is connected between
the RO pin and Vcc to reduce power dissipated in the IC.
Due to reasons related to the operation of circuits, the voltage
at this pin should be 2.5V or higher.
Consequently, the maximum resistance, RO
(max.)
, of load re-
sistor RO is:
Vcc
(min.)
–2.5 [V]
I
SW(max.)
[A]
RO
(max.)
[
] =
where I
SW(max.)
is the maximum of I
SW
. If, for example,
Vcc
(min.)
= 4.75V and I
SW(max.)
=120mA, RO
(max.)
=18.8
.
Accordingly, if the resistance of R
S
is selected so as to gain
maximum I
SW
of 120mA, RO should be 18.8
at the maxi-
mum.
6. Sample-Hold Circuit
(1) Circuit Operation Overview
The following is an overview of the operation of the sample-
hold circuit contained in the M66515.
The PD current generated by LD illumination flows through
the resistor connected between 1RM and 2RM, thereby gen-
erating a potential difference (V
M
). V
M
is compared with the
voltage applied to the Vr pin. If V
M
< Vr, a constant current is
sourced through the C
H
pin so that the external capacitor is
charged. If V
M
> Vr, a constant current sinks through the C
H
pin to discharge the external capacitor.This operation occurs
when the S/H input is “L” (sample). When the S/H input is “H,”
the C
H
pin is maintained at high impedance state (hold), irre-
spective of the state of V
M
, Vr, and DATA input.
Reference voltage input
Potential difference on resistor RM
V
r
V
M
Comparator
+
Control
circuit
S/H
Sample-hold
control input
ENB
SW1
SW2
C
H
T
r1
Externat capacitor
Constant current
source for charging
Constant current
source for discharging
Output
Conceptual Diagram : Sample-Hold circuit
相關PDF資料 |
PDF描述 |
|---|---|
| M66700P | DUAL HIGH-SPEED CCD CLOCK DRIVER |
| M66700WP | DUAL HIGH-SPEED CCD CLOCK DRIVER |
| M66701P | DUAL HIGH-SPEED CCD CLOCK DRIVER |
| M66851FP | SRAM TYPE FIFO MEMORY |
| M66850FP | SRAM TYPE FIFO MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M66515FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:LASER-DIODE DRIVER/CONTROLLER |
| M66515FP#TC2J | 功能描述:IC LASR CTRLR 40MBPS 5.25V 20SOP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| M66515FP(#TC2J) | 制造商:Renesas Electronics Corporation 功能描述: |
| M66516FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:LASER-DIODE DRIVER/CONTROLLER |
| M6657 | 制造商:Tamura Corporation of America 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。