參數資料
型號： M7020R-050ZA1T
廠商： 意法半導體
英文描述： CAP TANT 22UF 10V 20% POLY SMD
中文描述： 32K的× 68位進入網絡搜索引擎
文件頁數： 92/150頁
文件大?。?/td> 996K
代理商： M7020R-050ZA1T
M7020R
92/150
272-bit SEARCH on Tables x272-configured Using Up to Eight M7020R Devices
The hardware diagram of the search subsystem of
eight devices is shown in Figure 66, page 94. The
following are the parameters programmed in the
eight devices.
– First seven devices (devices 0–6):
CFG = 10101010, TLSZ = 01, HLAT = 000,
LRAM = 0, and LDEV = 0.
– Eighth device (device 7):
CFG = 10101010, TLSZ = 01, HLAT = 000,
LRAM = 1, and LDEV = 1.
Note:
All eight devices must be programmed with
the same value of TLSZ and HLAT. Only the last
device in the table must be programmed with
LRAM = 1 and LDEV = 1 (Device 7 in this case).
All other upstream devices must be programmed
with LRAM = 0 and LDEV = 0 (Devices 0 through
6 in this case).
Figure 68, page 96 shows the timing diagram for a
SEARCH command in the 272-bit-configured ta-
ble of eight devices for Device 0. Figure 69, page
97 shows the timing diagram for a SEARCH com-
mand in the 272-bit-configured table of eight de-
vices for Device 1. Figure 70, page 98 shows the
timing diagram for a SEARCH command in the
272-bit-configured table of eight devices for De-
vice 7 (the last device in this specific table). For
these timing diagrams three 272-bit searches are
performed sequentially. The following HIT/MISS
assumptions were made as shown in Table 43,
page 93.
The following is the sequence of operation for a
single 272-bit SEARCH command (also COM-
MAND CODES AND PARAMETERS, page 29).
–
Cycle A:
The host ASIC drives the CMDV high
and applies SEARCH command code ('10') on
CMD[1:0] signals. CMD[5:3] signals must be
driven with the index to the GMR pair used for
bits [271:136] of the data being searched in this
operation. DQ[67:0] must be driven with the 68-
bit data ([271:204]) to be compared against all
locations “0” in the four-word, 68-bit page. The
CMD[2] signal must be driven to logic '1.'
Note:
CMD[2] = 1 signals that the search is a
272-bit search. CMD[8:3] in this cycle is ig-
nored.
–
Cycle B:
The host ASIC continues to drive the
CMDV high and applies SEARCH command
code ('10') on CMD[1:0]. The DQ[67:0] is driven
with the 68-bit data ([203:136]) to be compared
against all locations “1” in the four 68-bits-word
page.
–
Cycle C:
The host ASIC drives the CMDV high
and applies SEARCH command code ('10') on
CMD[1:0] signals. CMD[5:3] signals must be
driven with the index to the GMR pair used for
bits [135:0] of the data being searched.
CMD[8:7] signals must be driven with the bits
that will be driven on SADR[21:20] by this de-
vice if it has a hit. DQ[67:0] must be driven with
the 68-bit data ([135:68]) to be compared
against all locations “2” in the four 68-bits-word
page. The CMD[2] signal must be driven to logic
'0.'
–
Cycle D:
The host ASIC continues to drive the
CMDV high and applies SEARCH command
code ('10') on CMD[1:0]. CMD[8:6] signals must
be driven with the index of the SSR that will be
used for storing the address of the matching en-
try and the Hit Flag (see SEARCH-Successful
Registers (SSR[0:7]), page 23). The DQ[67:0] is
driven with the 68-bit data ([67:0]) to be com-
pared to all locations “3” in the four 68-bits-word
page. CMD[5:2] is ignored because the LEARN
Instruction is not supported for x272 tables.
Note:
For 272-bit searches, the host ASIC must
supply four distinct 68-bit data words on
DQ[67:0] during Cycles A, B, C, and D. The
GMR Index in Cycle A selects a pair of GMRs in
each of the eight devices that apply to DQ data
in Cycles A and B. The GMR Index in Cycle C
selects a pair of GMRs in each of the eight de-
vices that apply to DQ data in Cycles C and D.
The logical 272-bit SEARCH operation is shown in
Figure 67, page 95. The entire table of 272-bit en-
tries is compared to a 272-bit word K that is pre-
sented on the DQ Bus in Cycles A, B, C, and D of
the command using the GMR and the local mask
bits. The GMR is the 272-bit word specified by the
two pairs of GMRs selected by the GMR Indexes
in the command’s Cycles A and C in each of the
eight devices. The 272-bit word K that is presented
on the DQ Bus in Cycles A, B, C, and D of the com-
mand is compared to each entry in the table start-
ing at location “0.” The first matching entry’s
location address, “L,” is the winning address that is
driven as part of the SRAM address on the
SADR[23:0] lines (see SRAM ADDRESSING,
page 126).
Note:
The matching address is always going to be
a location “0” in a four-entry page for 272-bit
SEARCH (two LSBs of the matching index will be
'00').
相關PDF資料
PDF描述
M7020R-066ZA1T 32K x 68-bit Entry NETWORK SEARCH ENGINE
M7020R-083ZA1T 32K x 68-bit Entry NETWORK SEARCH ENGINE
M7020R 32K x 68-bit Entry NETWORK SEARCH ENGINE
M72DW64000B 64Mbit (x8/ x16, Multiple Bank, Boot Block) Flash Memory and 16Mbit Pseudo SRAM, 3V Supply, Multiple Memory Product
M72DW64000B70ZT 64Mbit (x8/ x16, Multiple Bank, Boot Block) Flash Memory and 16Mbit Pseudo SRAM, 3V Supply, Multiple Memory Product
相關代理商/技術參數
參數描述
M7020R-066ZA1T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32K x 68-bit Entry NETWORK SEARCH ENGINE
M7020R-083ZA1T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32K x 68-bit Entry NETWORK SEARCH ENGINE
M702-230442 功能描述:火線接頭 IEEE 1394 SMT 4P HORIZONTAL RoHS:否 制造商:Molex 產品:IEEE 1394 Firewire Connectors 標準:IEEE 1394 位置/觸點數量:6 節距:2 mm 觸點電鍍:Unplated 觸點材料:Phosphor Bronze 型式:Female 電流額定值:0.5 A 安裝風格:Through Hole 端接類型:Solder Tab 連接器類型:Firewire Receptacle
M702-230642 功能描述:火線接頭 IEEE 1394 SMT 6P HORIZONTAL RoHS:否 制造商:Molex 產品:IEEE 1394 Firewire Connectors 標準:IEEE 1394 位置/觸點數量:6 節距:2 mm 觸點電鍍:Unplated 觸點材料:Phosphor Bronze 型式:Female 電流額定值:0.5 A 安裝風格:Through Hole 端接類型:Solder Tab 連接器類型:Firewire Receptacle
M7023 制造商:Tamura Corporation of America 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*