參數資料
型號: M93C86-MN7
廠商: 意法半導體
英文描述: 16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM
中文描述: 16Kbit,8Kbit,4Kbit,2Kbit和1Kbit(8位或16位寬)MICROWIRE串行EEPROM的訪問
文件頁數: 11/31頁
文件大?。?/td> 259K
代理商: M93C86-MN7
11/31
M93C86, M93C76, M93C66, M93C56, M93C46
READY/BUSY STATUS
While the Write or Erase cycle is underway, for a
WRITE, ERASE, WRAL or ERAL instruction, the
Busy signal (Q=0) is returned whenever Chip Se-
lect Input (S) is driven High. (Please note, though,
that there is an initial delay, of t
SLSH
, before this
status information becomes available). In this
state, the M93Cx6 ignores any data on the bus.
When the Write cycle is completed, and Chip Se-
lect Input (S) is driven High, the Ready signal
(Q=1) indicates that the M93Cx6 is ready to re-
ceive the next instruction. Serial Data Output (Q)
remains set to 1 until the Chip Select Input (S) is
brought Low or until a new start bit is decoded.
COMMON I/O OPERATION
Serial Data Output (Q) and Serial Data Input (D)
can be connected together, through a current lim-
iting resistor, to form a common, single-wire data
bus. Some precautions must be taken when oper-
ating the memory in this way, mostly to prevent a
short circuit current from flowing when the last ad-
dress bit (A0) clashes with the first data bit on Se-
rial Data Output (Q). Please see the application
note
AN394
for details.
CLOCK PULSE COUNTER
In a noisy environment, the number of pulses re-
ceived on Serial Clock (C) may be greater than the
number delivered by the master (the microcontrol-
ler). This can lead to a misalignment of the instruc-
tion of one or more bits (as shown in
Figure 7.
) and
may lead to the writing of erroneous data at an er-
roneous address.
To combat this problem, the M93Cx6 has an on-
chip counter that counts the clock pulses from the
start bit until the falling edge of the Chip Select In-
put (S). If the number of clock pulses received is
not the number expected, the WRITE, ERASE,
ERAL or WRAL instruction is aborted, and the
contents of the memory are not modified.
The number of clock cycles expected for each in-
struction, and for each member of the M93Cx6
family, are summarized in
Table 5.
to
Table 7.
. For
example, a Write Data to Memory (WRITE) in-
struction on the M93C56 (or M93C66) expects 20
clock cycles (for the x8 organization) from the start
bit to the falling edge of Chip Select Input (S). That
is:
1 Start bit
+ 2 Op-code bits
+ 9 Address bits
+ 8 Data bits
Figure 7. Write Sequence with One Clock Glitch
AI01395
S
An-1
C
D
WRITE
START
D0
"1"
"0"
An
Glitch
An-2
ADDRESS AND DATA
ARE SHIFTED BY ONE BIT
相關PDF資料
PDF描述
M93C86-WDS6 16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM
M93C86-WDS7 16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM
M93C86-WDW3 16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM
M93C86-WDW6 16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM
M93C86-WDW7 16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM
相關代理商/技術參數
參數描述
M93C-86RBN6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM
M93C-86RBN7P 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM
M93C-86RDS3T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM
M93C86-RDS6TG 制造商:STMicroelectronics 功能描述:EEPROM SERL-MICROWIRE 16KBIT 2KX8 2.5V/3.3V/5V 8TSSOP - Tape and Reel
M93C86-RDW3TP/K 功能描述:EEPROM MICROWIRE 16KB 8TSSOP 制造商:stmicroelectronics 系列:- 包裝:剪切帶(CT) 零件狀態:有效 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:16K(2K x 8,1K x 16) 速度:2MHz 接口:Microwire 3 線串行 電壓 - 電源:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 125°C(TA) 封裝/外殼:8-TSSOP(0.173",4.40mm 寬) 供應商器件封裝:8-TSSOP 標準包裝:1