Controllers with I2C/SP" />
參數資料
型號： MAX11801ETC+
廠商： Maxim Integrated Products
文件頁數： 28/59頁
文件大?。?/td> 0K
描述： IC CTRLR TOUCH-SCREEN 12-TQFN
其它有關文件： Automotive Product Guide
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 75
類型： 電阻
觸摸面板接口： 4 線
輸入數/鍵： 1 TSC
分辨率（位）： 12 b
評估套件： 可供
數據接口： I²C，串行
數據速率/采樣率 (SPS，BPS)： 105k
電源電壓： 1.7 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 12-WQFN 裸露焊盤
供應商設備封裝： 12-TQFN-EP（4x4）
包裝： 管件
產品目錄頁面： 1424 (CN2011-ZH PDF)
MAX11800–MAX11803
Low-Power, Ultra-Small Resistive Touch-Screen
Controllers with I2C/SPI Interface
34
______________________________________________________________________________________
FIFO Data Word Structure
Table 11 shows a 16-bit data word (MSB byte + LSB
byte). Each data word consists of 12 bits of position
data, mapped to locations [15:4]. Eight-bit measure-
ment data are left-adjusted and mapped to locations
[15:8] and followed by four trailing zeros if averaging is
off. If averaging is on, the 4 bits contain random data as
a result of the summation and division process. Table
12 shows a 2-bit measurement tag indicating the mea-
surement type (X, Y, Z1, or Z2), appended in locations
[3:2]. Table 13 shows a 2-bit event tag indicating where
the sample occurs within a touch event (initial, mid-
press, or release) in locations [1:0].
All data for a given scan operation is tagged according
to the touch status observed at the end of the scan
block measurement operations. For example, if a
requested X, Y, Z1, Z2 scan block contains a release
event, all the data words are tagged 10 before being
written to the FIFO.
An event tag of 11 indicates that the data readback
operation reaches the end of the current FIFO data log
(end of file marker) and there is no unread data in the
FIFO. Terminate the readback operation to await the
next interrupt. Ignore all data with the 11 event tag.
Block Readback Operations
The MAX11800/MAX11801 do not support partial block
readback operations. Each readback operation loads
an entire scan block result (32, 48, or 64 bits) into a
temporary location for serial readback. A scan block is
marked as read in the FIFO once a scan block result is
loaded, freeing the memory space for the subsequent
measurements. Once initiated, the AP must complete
the full readback cycle for the block requested or the
unread portions of the block data is lost.
Clearing Interrupt
The FIFO is only used in the autonomous mode with the
clear-on-read interrupt. The interrupt is cleared only
when the newest data block currently available in the
FIFO is loaded for readback. The interrupt does not
clear if there is any unread data block remaining in the
FIFO once a scan block result is loaded. The FIFO does
not check for partial block readbacks. Once the last
available FIFO data block is loaded for readback, the
interrupt clears regardless of whether the readback
operation for that block is complete.
Aperture Modes and Options
The aperture modes available with the MAX11800/
MAX11801 implement spatial filtering. The MAX11800/
MAX11801 contain the required logic to examine panel
measurement data and determine if the data meets the
aperture requirements to be written to the FIFO. Aperture
testing decreases the number of entries in the FIFO to
the minimum required to implement the intended appli-
cation. The elimination of extraneous FIFO data events
reduces activity on the TIRQ line, serial bus, and mini-
mizes AP overhead. The contents in the FIFO are not
necessarily linearly sampled in time when the device is in
aperture mode.
Aperture Range Requirements
Program the aperture range requirements for both X
and Y through register 0x0B. Range requirements are
expressed as distance, in position LSBs. The blanking
aperture extends from the initial touch position, both
±
ΔX and ±ΔY with 12-bit resolution (1 LSB = 1/4096 of
the corresponding screen dimension). An aperture set-
ting of 0x00 effectively disables aperture checking with
all measurement data logged to the FIFO. Apertures
are specified in a power-of-two format:
ΔX = 2APRX[3:0]-1
and
ΔY = 2APRY[3:0]-1.
EVENT
TAG[1:0]
Initial touch
00
Midpress
01
Release (data invalid)
10
End of file indicator
(FIFO data invalid)
11
Table 13. FIFO Event Tags
MEASUREMENT
TAG[3:2]
X00
Y01
Z1
10
Z2
11
Table 12. FIFO Data Measurement Tags
INDEX
15
14
13
12
11
10
9
8
7
65
4321
0
Byte
MSB Byte
LSB Byte
12-Bit Content
Position MSBs
Position LSBs
Measure
Event
8-Bit Content
Position Data
Trailing Zeros*
Measure
Event
Table 11. FIFO Data Word Structure
*
When using averaging with 8-bit conversions, these positions may be filled with fractional data due to averaging operations.
相關PDF資料
PDF描述
VE-24P-IW-B1 CONVERTER MOD DC/DC 13.8V 100W
VI-BTK-IV-B1 CONVERTER MOD DC/DC 40V 150W
VE-JWD-MX-F3 CONVERTER MOD DC/DC 85V 75W
VI-BTH-IV-B1 CONVERTER MOD DC/DC 52V 150W
VI-BTF-IV-B1 CONVERTER MOD DC/DC 72V 150W
相關代理商/技術參數
參數描述
MAX11801ETC/V+ 功能描述:觸摸屏轉換器和控制器 I2C 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
MAX11801ETC/V+T 功能描述:觸摸屏轉換器和控制器 I2C 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
MAX11801ETC+ 功能描述:觸摸屏轉換器和控制器 I2C 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
MAX11801ETC+T 功能描述:觸摸屏轉換器和控制器 I2C 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
MAX11801EVKIT+ 功能描述:數據轉換 IC 開發工具 MAX11801 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*