- 您現在的位置：買賣IC網 > PDF目錄9462 > MAX127AEAI+T (Maxim Integrated Products)IC DAS 12BIT 2-WIRE 28-SSOP PDF資料下載
參數資料
| 型號： | MAX127AEAI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAS 12BIT 2-WIRE 28-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 類型： | 數據采集系統（DAS），ADC |
| 分辨率（位）： | 12 b |
| 采樣率（每秒）： | 8k |
| 數據接口： | I²C，串行 |
| 電壓電源： | 單電源 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 帶卷 (TR) |
MAX127/MAX128
To power-up from a software initiated power-down, a
START condition followed by the correct slave address
must be received (with R/W = 0). The MAX127/MAX128
power-up after receiving the next bit.
For hardware-controlled power-down (FULLPD), pull
SHDN low. When hardware shutdown is asserted, it
becomes effective immediately and any conversion in
progress is aborted.
Choosing Power-Down Modes
The bandgap reference and reference buffer remain
active in STBYPD mode, maintaining the voltage on the
4.7F capacitor at REF. This is a “DC” state that does
not degrade after standby power-down of any duration.
In FULLPD mode, only the bandgap reference is active.
Connect a 33F capacitor between REF and AGND to
maintain the reference voltage between conversions
and to reduce transients when the buffer is enabled
and disabled. Throughput rates down to 1ksps can be
achieved without allotting extra acquisition time for ref-
erence recovery prior to conversion. This allows con-
version to begin immediately after power-down ends. If
the discharge of the REF capacitor during FULLPD
exceeds the desired limits for accuracy (less than a
fraction of an LSB), run a STBYPD power-down cycle
prior to starting conversions. Take into account that the
reference buffer recharges the bypass capacitor at an
80mV/ms slew rate, and add 50s for settling time.
Auto-Shutdown
Selecting STBYPD on every conversion automatically
shuts the MAX127/MAX128 down after each conversion
without requiring any start-up time on the next conversion.
Multirange, +5V, 12-Bit DAS with
2-Wire Serial Interface
14
______________________________________________________________________________________
REF
10k
2.5V
CREF
4.7
F
2.5V
REFADJ
AV = 1.638
0.01
F
MAX127
MAX128
Figure 11c. External Reference, Reference at REFADJ
100k
510k
24k
REFADJ
+5V
0.01
F
MAX127
MAX128
Figure 12. Reference-Adjust Circuit
REF
10k
2.5V
CREF
4.7
F
0.01
F
REFADJ
AV = 1.638
MAX127
MAX128
Figure 11a. Internal Reference
REF
VDD
10k
2.5V
4.096V
CREF
4.7
F
REFADJ
AV = 1.638
MAX127
MAX128
Figure 11b. External Reference, Reference at REF
相關PDF資料 |
PDF描述 |
|---|---|
| MS3452L20-27P | CONN RCPT 14POS BOX MNT W/PINS |
| MAX196ACWI+T | IC DAS 12BIT 6CH 28-SOIC |
| MAX196BEWI+T | IC DAS 12BIT 6CH 28-SOIC |
| GTC020R-10SL-3P | CONN RCPT 3POS BOX MNT W/PINS |
| MAX199BEWI+T | IC DAS 12BIT 8CH 28-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX127AENG | 功能描述:數據轉換系統 RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127AENG+ | 功能描述:數據轉換系統 12-Bit 8Ch 8ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127BCAI | 功能描述:數據轉換系統 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127BCAI+ | 功能描述:數據轉換系統 12-Bit 8Ch 8ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127BCAI+ | 制造商:Maxim Integrated Products 功能描述:CONVERTOR AD ((NW)) |
發布緊急采購，3分鐘左右您將得到回復。