參數資料
型號： MAX1464AAI+T
廠商： Maxim Integrated Products
文件頁數： 15/47頁
文件大?。?/td> 0K
描述： IC SENSOR SIGNAL COND 28-SSOP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,000
類型： 信號調節器
輸入類型： 模擬
輸出類型： 邏輯
接口： SPI
電流 - 電源： 890µA
安裝類型： 表面貼裝
封裝/外殼： 28-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 28-SSOP
包裝： 帶卷 (TR)
MAX1464
Low-Power, Low-Noise Multichannel
Sensor Signal Processor
22
Maxim Integrated
Program and Coefficient Memory
The program and coefficient memory, FLASH partition 0,
is addressed by the CPU and by the serial interface
sequentially from 0000h (0 dec) to 0FFFh (4095 dec).
Program execution by the CPU always begins at address
0000h and proceeds toward 0FFFh in 1-byte increments.
Although both the CPU and the serial interface can
address a 16-bit field, the FLASH size only uses 12
bits. Therefore, the leading 4 MSBs of the address field
are ignored. It is advisable to have all leading bits of
the 16-bit address in PFAR[15:0] set to zero.
The FLASH memory in partition 0 can be erased in indi-
vidual 64-byte pages using the page-erase command,
or erased in bulk using the all-erase command. The
information data memory (partition 1) is unaffected by
any operation performed on partition 0.
Information Data Memory
The information data memory, FLASH partition 1, is
addressed by bytes sequentially from 00h (0 dec) to 7Fh
(127 dec). The addressed byte should have all leading
bits of the 16-bit address in PFAR[15:0] set to zero.
The FLASH memory in partition 1 has only two 64-byte
pages that can be erased separately using the page-
erase command, or erased together using the all-erase
command. Data in partition 0 is not affected by any
operation performed on partition 1.
MAX1464 CPU Instruction Set
The MAX1464 CPU has 16 instructions used to perform
all calculations for sensor compensation, linearization,
and signal output functions. Each instruction comprises
a 4-bit op code and a 4-bit CPU register address. The
op code describes what operation to perform; the reg-
ister address describes what register, or registers, to
perform the operation on.
Instruction Format
All instructions are single-byte instructions with the
exception of load data from instruction memory. LDX
fetches the 2 following bytes of instruction memory and
loads them into a register. This is how calibration and
compensation coefficients are stored within the
MAX1464. Any number of coefficients can be stored in
instruction memory. The instruction code format is as
follows:
Instruction Set Details
LDX
Load Register X
Op-code:
0000 XXXXBINARY 0Xh
Operation:
X-register
← [PC+1] : [PC+2]
PC-register
← PC + 3 (point to next instruction)
CPU Cycles required:
3 cycles
Instruction:
Loads the next 2 bytes of program memory into CPU
register X. Register X can be any of the 16 CPU regis-
ters. Program counter (PC) is incremented twice during
the fetches of the next 2 bytes and incremented a third
time to point to the next instruction in program memory.
Two’s-complement data format is preserved.
No branching occurs.
No other registers are affected.
CLX
Clear Register X
Op-code:
0001 XXXXBINARY 1Xh
Operation:
X-register
← 0000h
PC-register
← PC + 1 (point to next instruction)
CPU Cycles required:
1 cycle
Description:
Clear the contents of register X to 0000h.
Register X can be any of the 16 CPU registers.
PC is incremented once to point to the next instruction
in program memory.
Two’s-complement data format is preserved.
No branching occurs.
No other registers are affected.
ANX
AND Register X with Register A
Op-code:
0010 XXXXBINARY 2Xh
Operation:
A-register
← A-register AND X-register
PC-register
← PC + 1 (point to next instruction)
CPU Cycles required:
1 cycle
COMMAND OP CODE
(BITS 7–4)
REGISTER OP CODE
(BITS 3–0)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
MSB
LSB
相關PDF資料
PDF描述
MAX1474AXT+T IC ELECTRONIC CAPACITOR SC70-6
MAX14753EUE+T IC MULTIPLEXER DUAL 4X1 16TSSOP
MAX14756EUE+T IC ANLG SWITCH SPST QUAD 16TSSOP
MAX14759ETA+ IC SWITCH ANALOG 8-TDFN-EP
MAX14764ETA+T IC ANALOG SWITCH
相關代理商/技術參數
參數描述
MAX1464CAI 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MAX1464CAI+ 功能描述:數字信號處理器和控制器 - DSP, DSC Low-Power Low-Noise Multichannel Sensor Signal Processor RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MAX1464CAI+T 功能描述:數字信號處理器和控制器 - DSP, DSC Low-Power Low-Noise Multichannel Sensor Signal Processor RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MAX1464CAI-T 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MAX1464EAI 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*