- 您現在的位置：買賣IC網 > PDF目錄2009 > MAX19707ETM+T (Maxim Integrated Products)IC ANLG FRNT END 48-TQFN PDF資料下載
參數資料
| 型號： | MAX19707ETM+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 27/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ANLG FRNT END 48-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 10 |
| 通道數： | 4 |
| 功率（瓦特）： | 84.6mW |
| 電壓 - 電源，模擬： | 3V |
| 電壓 - 電源，數字： | 3V |
| 封裝/外殼： | 48-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-TQFN-EP（7x7） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
MAX19707
10-Bit, 45Msps, Ultra-Low-Power
Analog Front-End
______________________________________________________________________________________
33
ADC Gain Error
Ideally, the ADC full-scale transition occurs at 1.5 LSB
below full scale. The gain error is the amount of devia-
tion between the measured transition point and the
ideal transition point with the offset error removed.
ADC Dynamic Parameter Definitions
Aperture Jitter
Figure 14 shows the aperture jitter (tAJ), which is the
sample-to-sample variation in the aperture delay.
Aperture Delay
Aperture delay (tAD) is the time defined between the
rising edge of the sampling clock and the instant when
an actual sample is taken (Figure 14).
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error) and results directly
from the ADC’s resolution (N bits):
SNR(max) = 6.02 x N + 1.76
In reality, there are other noise sources besides quanti-
zation noise: thermal noise, reference noise, clock jitter,
etc. SNR is computed by taking the ratio of the RMS
signal to the RMS noise. RMS noise includes all spec-
tral components to the Nyquist frequency excluding the
fundamental, the first five harmonics, and the DC offset.
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS sig-
nal to the RMS noise. RMS noise includes all spectral
components to the Nyquist frequency excluding the
fundamental and the DC offset.
Effective Number of Bits (ENOB)
ENOB specifies the dynamic performance of an ADC at a
specific input frequency and sampling rate. An ideal
ADC’s error consists of quantization noise only. ENOB for
a full-scale sinusoidal input waveform is computed from:
ENOB = (SINAD - 1.76) / 6.02
Total Harmonic Distortion (THD)
THD is typically the ratio of the RMS sum of the first five
harmonics of the input signal to the fundamental itself.
This is expressed as:
where V1 is the fundamental amplitude and V2–V6 are
the amplitudes of the 2nd- through 6th-order harmonics.
Third Harmonic Distortion (HD3)
HD3 is defined as the ratio of the RMS value of the third
harmonic component to the fundamental input signal.
Spurious-Free Dynamic Range (SFDR)
SFDR is the ratio expressed in decibels of the RMS
amplitude of the fundamental (maximum signal compo-
nent) to the RMS value of the next-largest spurious
component, excluding DC offset.
Intermodulation Distortion (IMD)
IMD is the total power of the intermodulation products
relative to the total input power when two tones, f1 and f2,
are present at the inputs. The intermodulation products
are (f1 ±f2), (2 f1), (2 f2), (2 f1 ±f2), (2 f2 ±f1).
The individual input tone levels are at -7dBFS.
3rd-Order Intermodulation (IM3)
IM3 is the power of the worst 3rd-order intermodulation
product relative to the input power of either input tone
when two tones, f1 and f2, are present at the inputs. The
3rd-order intermodulation products are (2 x f1 ±f2), (2
f2 ±f1). The individual input tone levels are at -7dBFS.
THD
(V +V +V +V +V )
V
2
3
2
4
2
5
2
6
2
1
=×
20 log
HOLD
ANALOG
INPUT
SAMPLED
DATA (T/H)
T/H
tAD
tAJ
TRACK
CLK
Figure 14. T/H Aperture Timing
相關PDF資料 |
PDF描述 |
|---|---|
| MAX19708ETM+ | IC ANLG FRONT END 11MSPS 48-TQFN |
| MAX19710ETN+T | IC ANLG FRNT END 56-TQFN |
| MAX19711ETN+T | IC ANLG FRNT END 56-TQFN |
| MAX19712ETN+T | IC ANLG FRNT END 56-TQFN |
| MAX19713ETN+T | IC ANLG FRNT END 56-TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX19707EVCMOD2 | 功能描述:ADC / DAC多通道 Evaluation System for the MAX19707 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX19707EVCMODU | 功能描述:ADC / DAC多通道 Evaluation System for the MAX19707 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX19707EVKIT | 功能描述:數據轉換 IC 開發(fā)工具 Evaluation Kit for the MAX19705 MAX19706 MAX19707 MAX19708 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX19708ETM | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX19708ETM+ | 功能描述:ADC / DAC多通道 11Msps CODEC/AFE 1.8/2.7-3.3V RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
發(fā)布緊急采購，3分鐘左右您將得到回復。