- 您現在的位置：買賣IC網 > PDF目錄1938 > MAX3107EAG+ (Maxim Integrated Products)IC UART SPI/I2C 128 FIFO 24SSOP PDF資料下載
參數資料
| 型號： | MAX3107EAG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART SPI/I2C 128 FIFO 24SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 58 |
| 特點： | 內部振蕩器 |
| 通道數： | 4，QUART |
| FIFO's： | 128 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.35 V ~ 3.6 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 24-SSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
SPI/I2C UART with 128-Word FIFOs
Transmitter Flow Control
If auto transmitter control (FlowCtrl[5:4]) is enabled, the
receiver compares all received words with the XOFF and
XON characters. If a XOFF is received, the MAX3107
halts its transmitter from sending further data. The
receiver is not affected and continues reception. Upon
receiving an XON, the transmitter restarts sending data.
The received XON and XOFF characters are filtered out
and are not put into the receive FIFO, as they do not have
significance to the higher layer protocol. An interrupt is
not generated.
Turn the transmitter off (MODE1[1]) before enabling
transmitter control.
Receiver Flow Control
If auto receiver overflow control (FlowCtrl[7:6]) is enabled,
the MAX3107 automatically sends XOFF and XON con-
trol characters to the far-end UART to avoid receiver
overflow. XOFF1/XOFF2 are sent when the receive FIFO
fill level reaches the HALT value set in the FlowLvl regis-
ter. When the host controller reads data from the Receive
FIFO to a level equal to the RESUME level programmed
into the FlowLvl register, XON1/XON2 are automatically
sent to the far-end station to signal it to resume data
transmission.
If dual-character (XON1 and XON2/XOFF1 and XOFF2)
flow control is selected, XON1/XOFF1 are transmitted
before XON2/XOFF2.
FIFO Interrupt Triggering
Receive and transmit FIFO fill-dependent interrupts are
generated if FIFO trigger levels are defined. When the
number of words in the FIFOs reach or exceed a trigger
level, as programmed in FIFOTrgLvl, an ISR[3] or ISR[4]
interrupt is generated. There is no relationship between
the trigger levels and the HALT or RESUME levels.
The FIFO trigger level can, for example, be used for a
block data transfer, since it gives the host an indication
when a given block size of data is available for readout in
the teceive FIFO or available for transfer to the transmit FIFO.
Low-Power Standby Modes
The sleep and shutdown modes reduce power con-
sumption during periods of inactivity. In both sleep and
shutdown modes, the UART disables specific functional
blocks to reduce power consumption.
Forced Sleep Mode
In forced sleep mode, all UART-related on-chip clocking
is stopped. The following are inactive: the crystal oscilla-
tor, the PLL, the predivider, the receiver, and the transmitter.
The SPI/I2C interface and the registers remain active.
Thus, the host controller can access the resisters. To
enter sleep mode, set MODE1[5] to 1. To wake up, set
MODE1[5] to 0.
Autosleep Mode
The MAX3107 can be configured to operate in autosleep
mode by setting MODE1[6] to 1. In autosleep mode, the
MAX3107 automatically enters sleep mode when all the
following conditions are met:
Both FIFOs are empty.
There are no pending IRQ interrupts.
There is no activity on any input pins for a period equal
to 65,536 UART characters lengths.
The MAX3107 exits autosleep mode as soon as activity
is detected on any of the GPIO_, RX, or CTS inputs.
To manually wake up the MAX3107, set MODE1[6] to 0.
After wake-up is initiated, the internal clock starts up and
a period of time is needed for clock stabilization. The
STSInt[5]: ClockReady bit indicates when the clocks are
stable. If an external clock source is used, the STSInt[5]
bit does not indicate clock stability.
Shutdown Mode
Shutdown mode is the lowest power consumption mode.
In shutdown mode, all the MAX3107 circuitry is off. This
includes the I2C/SPI interface, the registers, the FIFOs,
and clocking circuitry. The LDO is kept on. To enter shut-
down mode, connect RST to DGND.
When the RST input is toggled high, the MAX3107 exits shut-
down mode. When the MAX3107 sets IRQ to logic-high, the
chip initialization is completed. The MAX3107 needs to be
reprogrammed following a shutdown. Keep V18 powered by
the internal LDO or an external 1.8V supply during shutdown.
Power-Up and IRQ
IRQ has two functions. During normal operation (MODE1[7]
is 1), IRQ operates as a hardware interrupt output, where-
by the IRQ is active when an interrupt is pending. An IRQ
interrupt is only produced during normal operation, if at
least one of the IRQEn interrupt enable bits are enabled.
During power-up or following a reset, IRQ has a differ-
ent function. It is held low until the MAX3107 is ready for
programming following an initialization delay. Once IRQ
goes high, the MAX3107 is ready to be programmed.
The MODE1[7]: IRQSel bit should then be set in order to
enable normal IRQ interrupt operation.
In polled mode, the RevID register can be polled to
check whether the MAX3107 is ready for operation. If
the controller gets a valid response from RevID, then the
MAX3107 is ready for operation.
22
Maxim Integrated
MAX3107
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3108EWA+T | IC UART |
| MAX3109ETJ+ | SEMICONDUCTOR OTHER |
| MAX310CPE | IC VIDEO MULTIPLEXER 8X1 16DIP |
| MAX3110EENI+G36 | IC UART SPI COMPAT 28-DIP |
| MAX3120CUA+ | IC TXRX INFRARED IRDA 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3107EAG+ | 功能描述:UART 接口集成電路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3107EAG+T | 功能描述:UART 接口集成電路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3107ETG/V+ | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3107ETG/V+T | 功能描述:UART 接口集成電路 SPI/IC UART with 128-Word FIFOs and Internal Oscillator RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3107ETG+ | 功能描述:UART 接口集成電路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。