- 您現在的位置：買賣IC網 > PDF目錄1938 > MAX3109ETJ+ (Maxim Integrated Products)SEMICONDUCTOR OTHER PDF資料下載
參數資料
| 型號： | MAX3109ETJ+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/66頁 |
| 文件大?。?/td> | 0K |
| 描述： | SEMICONDUCTOR OTHER |
| 標準包裝： | 60 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
Dual Serial UART with 128-Word FIFOs
MAX3109
22
Maxim Integrated
Enable and configure transmitter synchronization with
the TxSynch register. Triggering and synchronization
requires that the transmitters are disabled before the
trigger is received. This can be done by setting the
MODE1[1]: TxDisabl bit high or by using the auto trans-
mitter disable function (TxSynch[4] is logic 1).
Transmitter Synchronization
Synchronize multiple UARTs so that their transmitters
start transmission simultaneously by assigning a com-
mon trigger command to the UARTs that should be
synchronized.
Intrachip and Interchip Synchronization
Intrachip transmitter triggering occurs when the two UARTs
in a MAX3109 device are triggered by one command. This
type of synchronization is supported in both SPI and I2C
modes, as the trigger commands are global commands
that are received by both UARTs simultaneously.
Interchip transmitter triggering synchronizes UARTs in
different MAX3109 devices. This type of synchroniza-
tion is achievable in SPI mode only. Pull the CS input of
all the MAX3109 devices on the bus low during the SPI
master’s write trigger command so that the commands
are received by all UARTs on the shared SPI bus.
I2C protocol does not allow simultaneous addressing of
multiple devices.
Delayed Triggering
A delay can be programmed to postpone the start of
transmission after receiving an assigned trigger com-
mand. Set the delay by programming the SynchDelay1
and SynchDelay2 registers.
Trigger Accuracy
The delay between the time when the MAX3109 receives
a trigger command and the time when the associ-
ated transmitter starts transmission is made up of a fixed,
deterministic portion, and a variable, random component.
Figure 11. Setup and Hold Times in Auto Transceiver Direction Control
Figure 10. Auto Transceiver Direction Control
TX_
FIRST CHARACTER
LAST CHARACTER
RTS_
SETUP
HOLD
MAX3109
MAX14840E
TRANSMITTER
TX_
B
A
D
RTS_
RX_
TxFIFO
RECEIVER
AUTO
TRANSCEIVER
CONTROL
RxFIFO
DI
RO
RE
DE
R
相關PDF資料 |
PDF描述 |
|---|---|
| MAX310CPE | IC VIDEO MULTIPLEXER 8X1 16DIP |
| MAX3110EENI+G36 | IC UART SPI COMPAT 28-DIP |
| MAX3120CUA+ | IC TXRX INFRARED IRDA 8-UMAX |
| MAX3120EUA | IC TXRX 3V IRDA IR 3V 8-UMAX |
| MAX312ESE | IC SWITCH QUAD SPST 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3109ETJ+ | 功能描述:UART 接口集成電路 Dual Serial UART with 128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3109ETJ+T | 功能描述:UART 接口集成電路 Dual Serial UART with 128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX310C/D | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX310CPE | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX310CPE+ | 功能描述:多路器開關 IC 8:1 Unbuffered RF Video MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。