參數資料
型號： MAX3353EEBP-T
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 穩壓器
英文描述： USB On-the-Go Charge Pump with Switchable Pullup/Pulldown Resistors
中文描述： 0.015 A SWITCHED CAPACITOR REGULATOR, 600 kHz SWITCHING FREQ-MAX, PBGA20
封裝： UCSP-20
文件頁數： 9/21頁
文件大小： 386K
代理商： MAX3353EEBP-T
charge pump on and off to power V
BUS
. Bit 4 in control
register 2 (V
BUS_DISCHG
) is used to discharge V
BUS
through a 5k
resistor. Figure 2 and Table 2 show
power control.
Autoconnect and Autoresponse
USB OTG defines the HNP, where the default host (A
Device) can pass the host responsibilities off to the
default peripheral (B Device). This protocol can be han-
dled entirely by the firmware and controlling logic that dri-
ves the OTG transceiver. The MAX3353E has the option
to automatically perform some of the required signaling
for some of the timing-critical events in the HNP process.
The automatic signaling used by the A Device, when it
transfers host control to the B Device, is defined by the
OTG transceiver supplement and is known as autocon-
nect. Autoconnect allows the transceiver to automatically
connect the A Device
’
s D+ pullup resistor during HNP.
Autoconnect is enabled when the MAX3353E is config-
ured as an A Device (ID_IN = 0) and the BDISC_ACONN
control bit is set.
The MAX3353E also has the capability to automate the
signaling used by the B Device when it assumes host
control from the A Device. This autoresponse is not speci-
fied by the OTG-transceiver supplement. Autoresponse
causes the B Device to automatically assert a bus reset
by driving a single-ended zero (SE0: both D+ and D- dri-
ven low) onto USB in response to the A Device connect-
ing its D+ pullup resistor. Autoresponse is enabled when
the MAX3353E is configured as a B Device and the
BDISC_ACONN control bit is set.
Note:
In a system, D+ and D- are also driven by a trans-
ceiver in an ASIC or other device. The autoresponse
mode should not be used unless the system designer
can ensure that there is no bus conflict between the
transceiver and the MAX3353E driving USB to SE0.
Autoconnect Details
When the MAX3353E is configured as an A Device
(ID_IN = GND), it can enable autodetect by setting
BDISC_ACONN to one. This should be done after the
USB is in the suspend state (>3ms with no traffic). The
MAX3353E monitors D+/D- for an SE0. The presence of
the SE0 indicates that the B Device has disconnected
its pullup resistor, the first step in HNP. When SE0 is
detected, the MAX3353E automatically turns on its
internal pullup resistor to the D+ line within 3ms. There
are two ways for firmware to ascertain that the
MAX3353E has automatically turned on its D+ pullup
during HNP:
1) The A_HNP status bit goes high when the D+ pullup
is automatically connected during HNP
2) The A_HNP_EN control bit is set, and an interrupt is
issued as the D+ pullup is connected (see also the
Interrupt Logic
section).
By clearing BDISC_ACONN bit, the D+ pullup is discon-
nected. After a successful autoconnect operation, the
firmware should set the DP_PULLUP control bit before
clearing the BDISC_ACONN bit; this ensures that the
D+ pullup remains connected.
Note:
The autoconnect works only if MAX3353E is not
in shutdown.
Autoresponse Details
When the MAX3353E is configured as a B Device
(ID_IN = open), setting the BDISC_ACONN control bit
enables the autoresponse feature. Using this feature,
the MAX3353E automatically issues a USB bus reset
when the A Device becomes a peripheral. Firmware
can take advantage of the autoresponse feature of the
MAX3353E by doing the following:
Ensure that the system transceiver is in USB-sus-
pend mode. Wait until the USB-suspend conditions
are met (no USB activity for >3ms). Enable auto-
response. Set the BDISC_ACONN control bit. Signal
a USB disconnect. Firmware clears the DP_PULLUP
control bit, which disconnects the D+ pullup resis-
tor. At this point, the MAX3353E waits at least 25μs
before enabling its internal USB line monitor to
detect if the A Device has attached its D+ pullup;
this ensures that the D+ line is not high due to the
residual effect of the B Device pullup. When the A
Device has connected its D+ pullup, the MAX3353E
issues a bus reset (SE0) and the B_HNP status bit
goes high.
Wait for B_HNP to go high; output SE0 from the
ASIC or other device on D+/D-. Disable autore-
sponse. By clearing BDISC_ACONN bit, the SE0
generator is turned off. The SE0 is maintained by the
system USB transceiver.
Note:
The autoresponse works only if the MAX3353E is
not in shutdown.
SRP V
BUS
Pulsing
Session request protocol (SRP) is designed to allow
the A Device (default host) to conserve power by turn-
ing off V
BUS
when there is no USB traffic. The B Device
(default peripheral) can request the A Device to turn
V
BUS
on and initiate a new session through SRP.
The B Device must initiate SRP in two ways: data-line
and V
BUS
pulsing. Firmware is responsible for turning
on and off the pullup resistor on D+ to implement
data-line pulsing. Firmware can also be used to turn on
and off a current source to implement V
BUS
pulsing.
M
USB On-the-Go Charge Pump with Switchable
Pullup/Pulldown Resistors
_______________________________________________________________________________________
9
相關PDF資料
PDF描述
MAX3353EEUE USB On-the-Go Charge Pump with Switchable Pullup/Pulldown Resistors
MAX3355EEUD +/-15kV ESD-Protected USB On-the-Go Charge Pump and Comparators in UCSP
MAX3386EEUP 3.0V, 【15kV ESD-Protected RS-232 Transceiver for PDAs and Cell Phones
MAX3386E Dual LVDS Receiver 8-SOIC -40 to 85
MAX3386ECUP Dual LVDS Receiver 8-MSOP -40 to 85
相關代理商/技術參數
參數描述
MAX3353EERP+ 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO CHARGE PUMP WITH SWITCHABLE PULLUP/PULLDOWN RE - Rail/Tube
MAX3353EERP+T 功能描述:低壓差穩壓器 - LDO USB On-the-Go Charge Pump with Switchable Pullup/Pulldown Resistors RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MAX3353EETI+ 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO CHARGE PUMP WITH SWITCHABLE PULLUP/PULLDOWN RE - Rail/Tube
MAX3353EEUE 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MAX3353EEUE+ 功能描述:電荷泵 USB On-the-Go Charge Pump RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*