- 您現在的位置：買賣IC網 > PDF目錄9674 > MAX3873AETP+ (Maxim Integrated Products)IC RECOV/RETIME 2.5GBPS 20TQFN PDF資料下載
參數資料
| 型號： | MAX3873AETP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RECOV/RETIME 2.5GBPS 20TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 75 |
| 類型： | 時鐘和數據恢復（CDR） |
| PLL： | 是 |
| 主要目的： | SONET/SDH |
| 輸入： | CML |
| 輸出： | CML |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:2 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 2.67Gbps |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 20-TQFN-EP（4x4） |
| 包裝： | 管件 |
MAX3873A
Detailed Description
The MAX3873A consists of a fully integrated phase-
locked loop (PLL), input amplifier, and CML output
buffers (Figure 5). The PLL consists of a phase/fre-
quency detector, a loop filter, and a voltage-controlled
oscillator (VCO).
This device is designed to deliver the best combination
of jitter performance and power dissipation by using a
fully differential signal architecture and low-noise
design techniques.
Input Amplifier
The input amplifier provides internal 50
Ω line termina-
tions and can accept a differential input amplitude from
50mVP-P to 1600mVP-P. The structure of the input
amplifier is shown in Figure 9.
Phase Detector
The phase detector incorporated in the MAX3873A pro-
duces a voltage proportional to the phase difference
between the incoming data and the internal clock.
Because of its feedback nature, the PLL drives the
error voltage to zero, aligning the recovered clock to
the center of the incoming data eye for retiming.
Frequency Detector
The digital frequency detector (FD) aids frequency
acquisition during startup conditions. The frequency
difference between the received data and the VCO
clock is derived by sampling the VCO outputs on each
edge of the data input signal. The FD drives the VCO
until the frequency difference is reduced to zero. Once
frequency acquisition is complete, the FD returns to a
neutral state.
Loop Filter and VCO
The phase detector and frequency detector outputs are
summed into the loop filter. An external capacitor, CF,
is required to set the PLL damping ratio. See the
Design Procedure section for guidelines on selecting
this capacitor.
Low-Power, Compact 2.5Gbps or 2.7Gbps
Clock-Recovery and Data-Retiming IC
_______________________________________________________________________________________
7
PIN
NAME
FUNCTION
10
SCLKEN
Clock Output Enable, TTL Input. When SCLKEN = open or SCLKEN = high, the clock outputs
(SCLKO±) are enabled. When SCLKEN = low, the clock outputs are disabled and SCLKO± = VCC.
11
SCLKO-
Negative Clock Output, CML. This output can be disabled by setting SCLKEN to low.
12
SCLKO+
Positive Clock Output, CML. This output can be disabled by setting SCLKEN to low.
13
VCC_BUF
3.3V CML Output Buffer Supply Voltage
14
SDO-
Negative Data Output, CML
15
SDO+
Positive Data Output, CML
16
LOL
Loss-of-Lock Output, TTL (Active Low). The LOL output indicates a PLL lock failure.
17, 20
GND
Supply Ground
18
FIL-
Negative PLL Loop Filter Connection. Connect a 0.022F capacitor between FIL+ and FIL-.
19
FIL+
Positive PLL Loop Filter Connection. Connect a 0.022F capacitor between FIL+ and FIL-.
EP
Exposed Pad
Ground. The exposed pad must be soldered to the circuit board ground for proper electrical and
thermal operation.
Pin Description (continued)
Figure 5. Functional Diagram
RATESET
FIL-
FIL+
GND
VCC
MAX3873A
LOOP
FILTER
FASTRACK
SDO+
SDO-
SDI+
SDI-
SCLKO+
SCLKO-
SCLKEN
MODE
AMP
I
Q
PHASE AND
FREQUENCY
DETECTOR
LOL
VCO
相關PDF資料 |
PDF描述 |
|---|---|
| MS3452L24-22P | CONN RCPT 4POS BOX MNT W/PINS |
| MS3101E32-15P | CONN RCPT 8POS FREE HNG W/PINS |
| MS27467E15A97S | CONN PLUG 12POS STRAIGHT W/SCKT |
| MS27468P15B35P | CONN RCPT 37POS JAM NUT W/PINS |
| MS3456L12S-3SW | CONN PLUG 2POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3873AETP+ | 功能描述:計時器和支持產品 2.5/2.7Gbps Clk-Reco & Data-Retiming IC RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MAX3873AETP+T | 功能描述:計時器和支持產品 2.5/2.7Gbps Clk-Reco & Data-Retiming IC RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MAX3873AEVKIT | 功能描述:計時器和支持產品 Evaluation Kit for the MAX3873A RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MAX3873EGP | 功能描述:計時器和支持產品 RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MAX3873EGP-T | 功能描述:計時器和支持產品 RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。