- 您現在的位置：買賣IC網 > PDF目錄8576 > MAX4032EUT+T (Maxim Integrated Products)IC VIDEO BUFFER 6DB SOT23-6 PDF資料下載
參數資料
| 型號： | MAX4032EUT+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC VIDEO BUFFER 6DB SOT23-6 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 應用： | 緩沖器 |
| 電路數： | 1 |
| -3db帶寬： | 55MHz |
| 轉換速率： | 275 V/µs |
| 電流 - 電源： | 6.5mA |
| 電流 - 輸出 / 通道： | 85mA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-6 |
| 供應商設備封裝： | SOT-6 |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1423 (CN2011-ZH PDF) |
| 其它名稱： | MAX4032EUT+TDKR |
MAX4032
5V, 6dB Video Buffer with Sync-Tip Clamp,
Output Sag Correction, and 150nA Shutdown Current
6
_______________________________________________________________________________________
Detailed Description
The MAX4032 5V, 6dB video buffer with sync-tip
clamp, output sag correction, and low-power shutdown
mode is available in tiny SOT23 and SC70 packages.
The sag-corrected output of the MAX4032 is designed
to drive AC-coupled, 150
back-terminated video
loads in portable video applications such as digital still
cams, portable DVD players, digital camcorders,
PDAs, video-enabled cell phones, portable game sys-
tems, and notebook computers. The sag correction
feature introduces low-frequency compensation that
reduces the value of the normally bulky and expensive
330F AC-coupling capacitor to two small, less expen-
sive 22F capacitors. The input clamp positions the
video waveform at the output and allows the MAX4032
to be used as either an AC- or DC-coupled output driver.
The MAX4032 operates from a single 5V supply and
consumes only 6.5mA of supply current. The low-power
shutdown mode reduces the supply current to 150nA,
making the MAX4032 ideal for low-voltage, battery-
powered video applications.
The input signal to the MAX4032 is AC-coupled through
a capacitor into an active sync-tip clamp circuit, which
places the minimum of the video signal at approximate-
ly 0.38V. The output buffer amplifies the video signal
while still maintaining the 0.38V clamp voltage at the
output. For example, if VIN = 0.38V, then VOUT = 0.38V.
If VIN = (0.38V + 1V) = 1.38V, then VOUT = (0.38V + 2 X
(1V)) = 2.38V when SAG is shorted OUT.
There are two common output connections for the
MAX4032:
1) SAG is shorted to OUT and 150
is directly con-
nected from OUT to ground (see Figure 2).
2) Two capacitors and 150
are connected between
OUT, SAG, and ground (see Figure 3).
Sag Correction
Sag correction refers to the low-frequency compensa-
tion of the highpass filter formed by the 150
load of a
back-terminated coax and the output-coupling capaci-
tor. This break point must be low enough in frequency
to pass the Vertical Sync Interval (<25Hz for PAL and
<30Hz for NTSC) to avoid Field Tilt. Traditionally, the
break point is made <3~5Hz, and the coupling capaci-
tor must be very large, typically >330F. The MAX4032
reduces the value of this coupling capacitor, replacing
it with a pair of 22F capacitors. This is done by putting
a resistor network in series with the feedback, raising
the gain, and creating a high-impedance node at the
SAG output. This node is AC-coupled to the load in par-
allel with the normal output, as shown in Figure 3. This
allows the use of two smaller capacitors (COUT and
CSAG), typically 22F, substantially reducing the size of
the interface caps and their cost while retaining the low-
frequency response.
The minimum value of the output-coupling capacitor is
a function of the acceptable Field Tilt. In Figure 1, the
Field Tilt is given for several values of capacitance from
10F to 47F for comparison. Although values lower
than 22F may have acceptable Field Tilt, they are not
recommended, since tolerance, aging, and voltage
and temperature coefficients reduce the capacitance in
actual
applications.
Increasing
the
output-
coupling capacitors beyond 47F does not improve
performance.
Shutdown Mode
The MAX4032 features a low-power shutdown mode
(ISHDN = 150nA) for battery-powered/portable applica-
tions. Pulling the SHDN pin high enables the output.
Connecting the SHDN pin to ground (GND) disables
the output and places the MAX4032 into a low-power
shutdown mode.
Applications Information
Input Coupling the MAX4032
The MAX4032 input must be AC-coupled because the
input capacitor stores the clamp voltage. The MAX4032
requires a typical value of 0.1F for the input clamp to
meet the Line Droop specification. A minimum of a
ceramic capacitor with an X7R temperature coefficient is
recommended to avoid temperature-related problems
with Line Droop. For extended temperature operation,
such as outdoor applications, or where the impressed
Figure 1. Field Tilt vs. Output-Coupling Capacitance
FIELD
TIME
DISTOR
TION
IN
%
PEAK
TO
PEAK
(%)
COUPLING CAPACITANCE (
F)
100
20
40
60
80
10
20
30
40
50
相關PDF資料 |
PDF描述 |
|---|---|
| VI-23F-IV-F2 | CONVERTER MOD DC/DC 72V 150W |
| VE-B5L-MU | CONVERTER MOD DC/DC 28V 200W |
| VE-B5K-MU | CONVERTER MOD DC/DC 40V 200W |
| VI-23B-IV-F4 | CONVERTER MOD DC/DC 95V 150W |
| VI-233-IV-F3 | CONVERTER MOD DC/DC 24V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4032EXT | 制造商:Maxim Integrated Products 功能描述:5V 6DB VIDEO BUFFER W SYNC-TIP CLA - Cut Tape Product |
| MAX4032EXT+ | 制造商:Maxim Integrated Products 功能描述:VID BFFR 6PIN SC-70 - Rail/Tube |
| MAX4032EXT+T | 功能描述:視頻放大器 5V 6dB Video Buffer With Sync-Tip Clamp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX4032EXT-T | 功能描述:視頻放大器 RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX40-33CA | 制造商:MDE 制造商全稱:MDE Semiconductor, Inc. 功能描述:HIGH CURRENT TRANSIENT VOLTAGE SUPPRESSOR (TVS) DIODE STAND-OFF VOLTAGE 12 TO 150 Volts 40000 Watt Peak Pulse Power |
發布緊急采購，3分鐘左右您將得到回復。