- 您現在的位置：買賣IC網 > PDF目錄9178 > MAX5484EUD+T (Maxim Integrated Products)IC POT DGTL 10BIT NV 14-TSSOP PDF資料下載
參數資料
| 型號： | MAX5484EUD+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 10BIT NV 14-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 接片： | 1024 |
| 電阻（歐姆）： | 50k |
| 電路數： | 1 |
| 溫度系數： | 標準值 35 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線串行（芯片選擇，遞增，增/減） |
| 電源電壓： | 2.7 V ~ 5.25 V，±2.5 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
10-Bit, Nonvolatile, Linear-Taper Digital
Potentiometers
Copy Wiper Register to NV Register
The copy wiper register to NV register command (C1,
C0 = 10) stores the current position of the wiper to the
NV register for use at power-up. Figure 6 shows how to
copy data from wiper register to NV register. The oper-
ation takes up to 12ms (max) after
CS goes high to
complete and no other operation should be performed
until completion.
Copy NV Register to Wiper Register
The copy NV register to wiper register (C1, C0 = 11)
restores the wiper position to the current value stored in
the NV register. Figure 7 shows how to copy data from
the NV register to the wiper register.
Digital Up/Down Interface
Figure 8 illustrates an up/down serial-interface timing
diagram. In digital up/down interface mode (SPI/
UD =
0), the logic inputs
CS, DIN(U/D), and SCLK(INC) con-
trol the wiper position and store it in nonvolatile memory
(see Table 3). The chip-select (
CS) input enables the
serial interface when low and disables the interface
when high. The position of the wiper is stored in the
nonvolatile register when
CS transitions from low to
high while SCLK(
INC) is high.
When the serial interface is active (
CS low), a high-to-
low (falling edge) transition on SCLK(
INC) increments
or decrements the internal 10-bit counter depending on
the state of DIN(U/
D). If DIN(U/D) is high, the wiper
increments. If DIN(U/
D) is low, the wiper decrements.
The device stores the value of the wiper position in the
nonvolatile memory when
CS transitions from low to high
while SCLK(
INC) is high. The host system can disable
the serial interface and deselect the device without stor-
ing the latest wiper position in the nonvolatile memory by
keeping SCLK(
INC) low while taking CS high.
Upon power-up, the MAX5481–MAX5484 load the
value of nonvolatile memory into the wiper register, and
set the wiper position to the value last stored.
ACTION
00
1
0
00
0
12
3
4
5
6
78
CS
C1
C0
WRITE NV
REGISTER
(DEVICE IS
BUSY)
tBUSY
SCLK(INC)
DIN(U/D)
Figure 6. Copy Wiper Register to NV Register Operation
CS
DIN(U/D)
SCLK(INC)W
LL
↓
Decrement
LH
↓
Increment
LX
↑
No Change
H
X
No Change
↓
X
No Change
↑
X
L
Position Not Stored
↑
X
H
Position Stored
Table 3. Truth Table
↑ = Low-to-high transition.
↓ = High-to-low transition.
X
= Don’t care.
ACTION
00
1
00
0
12
3
4
5
6
78
CS
C1
C0
WIPER
REGISTER
UPDATED
SCLK(INC)
DIN(U/D)
Figure 7. Copy NV Register to Wiper Register Operation
MAX5481–MAX5484
16
Maxim Integrated
相關PDF資料 |
PDF描述 |
|---|---|
| M83723/91W2025N | CONN PLUG 25POS STRAIGHT W/SCKT |
| 7SB384BMX1TCG | 1 BIT DIGITAL SWITCH 6UDFN |
| 7SB384AMX1TCG | 1 BIT DIGITAL SWITCH ULLGA6 |
| 7SB3126CMX1TCG | 1 BIT BUS SWITCH ULLGA 6 |
| MAX5483EUD+T | IC POT DGTL 10BIT NV 14-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5486EUG+ | 功能描述:數字電位計 IC Stereo Vol Control w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5486EUG+T | 功能描述:數字電位計 IC Stereo Vol Control w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5487ETE | 制造商:Maxim Integrated Products 功能描述:DUAL 256-TAP SPI 10K DIGITAL POTENTIOMETER - Rail/Tube |
| MAX5487ETE#G16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5487ETE#TG16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。