參數資料
型號： MAX6873ETJ
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 電源管理
英文描述： EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors with Charge-Pump Outputs
中文描述： 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC32
封裝： 7 X 7 MM, 0.80 MM HEIGHT, MO-220, TQFN-32
文件頁數： 9/48頁
文件大?。?/td> 374K
代理商： MAX6873ETJ
MAX6872/MAX6873
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
______________________________________________________________________________________
17
when that output is logic-high. No output can depend
solely on MR.
The positive voltage monitors generate fault signals
(logical 0) to the MAX6872/MAX6873s’ logic array when
an input voltage is below the programmed undervolt-
age threshold, or when that voltage is above the over-
voltage threshold. The negative voltage monitor (IN2)
generates a fault signal to the logic array when the
input voltage is less negative than the undervoltage
threshold, or when that voltage is more negative than
the overvoltage threshold.
Registers 0Eh through 3Ah and 40h configure each of
the programmable outputs. Programmable timing
blocks set the PO_ timeout period from 25s to 1600ms
Table 7. Programmable Output Behavior and MARGIN
REGISTER
ADDRESS
EEPROM
MEMORY
ADDRESS
BIT
RANGE
AFFECTED OUTPUT
DESCRIPTION
[0]
PO1
(MAX6872 only)
0 = output held in existing state.
1 = output asserts high or low (see 42h[0]).
[1]
PO2
(MAX6872 only)
0 = output held in existing state.
1 = output asserts high or low (see 42h[1]).
[2]
PO3 (MAX6872)
PO1 (MAX6873)
0 = output held in existing state.
1 = output asserts high or low (see 42h[2]).
[3]
PO4 (MAX6872)
PO2 (MAX6873)
0 = output held in existing state.
1 = output asserts high or low (see 42h[3]).
[4]
PO5 (MAX6872)
PO3 (MAX6873)
0 = output held in existing state.
1 = output asserts high or low (see 42h[4]).
[5]
PO6 (MAX6872)
PO4 (MAX6873)
0 = output held in existing state.
1 = output asserts high or low (see 42h[5]).
[6]
PO7 (MAX6872)
PO5 (MAX6873)
0 = output held in existing state.
1 = output asserts high or low (see 42h[6]).
41h
8041h
[7]
PO8
(MAX6872 only)
0 = output held in existing state.
1 = output asserts high or low (see 42h[7]).
[0]
PO1
(MAX6872 only)
0 = output asserts low if 41h[0] = 1.
1 = output asserts high if 41h[0] = 1.
[1]
PO2
(MAX6872 only)
0 = output asserts low if 41h[1] = 1.
1 = output asserts high if 41h[1] = 1.
[2]
PO3 (MAX6872)
PO1 (MAX6873)
0 = output asserts low if 41h[2] = 1.
1 = output asserts high if 41h[2] = 1.
[3]
PO4 (MAX6872)
PO2 (MAX6873)
0 = output asserts low if 41h[3] = 1.
1 = output asserts high if 41h[3] = 1.
[4]
PO5 (MAX6872)
PO3 (MAX6873)
0 = output asserts low if 41h[4] = 1.
1 = output asserts high if 41h[4] = 1.
[5]
PO6 (MAX6872)
PO4 (MAX6873)
0 = output asserts low if 41h[5] = 1.
1 = output asserts high if 41h[5] = 1.
[6]
PO7 (MAX6872)
PO5 (MAX6873)
0 = output asserts low if 41h[6] = 1.
1 = output asserts high if 41h[6] = 1.
42h
8042h
[7]
PO8
(MAX6872 only)
0 = output asserts low if 41h[7] = 1.
1 = output asserts high if 41h[7] = 1.
相關PDF資料
PDF描述
MAX6874ETJ EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors
MAX6876ETX EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit
MAX6884ETP EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC
MAX6884ETP-T EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC
MAX6885ETP EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC
相關代理商/技術參數
參數描述
MAX6873ETJ+ 功能描述:監控電路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6873ETJ+T 功能描述:監控電路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6873ETJ-T 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6874ETJ 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6874ETJ+ 功能描述:監控電路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*