- 您現在的位置：買賣IC網 > PDF目錄385547 > MAX691A (Maxim Integrated Products, Inc.) Microprocessor Supervisory Circuits(帶看門狗復位、片選和支持備用電池的復位器) PDF資料下載
參數資料
| 型號： | MAX691A |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Microprocessor Supervisory Circuits(帶看門狗復位、片選和支持備用電池的復位器) |
| 中文描述： | 微處理器監控電路 |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 164K |
| 代理商： | MAX691A |
M
Mic roproc essor S upervisory Circ uits
______________________________________________________________________________________
15
Maximum V
CC
Fall T ime
The V
fall time is limited by the propagation delay of
the battery switchover comparator and should not
exceed 0.03V/μs. A standard rule of thumb for filter
capacitance on most regulators is on the order of 100μF
per amp of current. When the power supply is shut off or
the main battery is disconnected, the associated initial
V
fall rate is just the inverse or 1A/100μF = 0.01V/μs.
The V
fall rate decreases with time as V
falls expo-
nentially, which more than satisfies the maximum fall-time
requirement.
Watc hdog S oftware Considerations
A way to help the watchdog timer keep a closer watch
on software execution involves setting and resetting the
watchdog input at different points in the program,
rather than “pulsing” the watchdog input high-low-high
or low-high-low. This technique avoids a “stuck” loop
where the watchdog timer continues to be reset within
the loop, keeping the watchdog from timing out. Figure
14 shows an example flow diagram where the I/O dri-
ving the watchdog input is set high at the beginning of
the program, set low at the beginning of every subrou-
tine or loop, then set high again when the program
returns to the beginning. If the program should “hang”
in any subroutine, the I/O is continually set low and the
watchdog timer is allowed to time out, causing a reset
or interrupt to be issued.
START
SET
WDI
LOW
RETURN
END
SUBROUTINE
OR PROGRAM LOOP
SET WDI
HIGH
Figure 14. Watchdog Flow Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6954APL | 4-Wire Interfaced, 2.7V to 5.5V LED Display Driver with I/O Expander and Key Scan |
| MAX6954 | Dual 4-Bit Decade And Binary Counters 16-CFP -55 to 125 |
| MAX6954AAX | Dual 4-Bit Decade And Binary Counters 20-LCCC -55 to 125 |
| MAX6957 | 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander |
| MAX6957AAI | 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX691AC/D | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX691ACPE | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX691ACPE+ | 功能描述:監控電路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX691ACSE | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX691ACSE+ | 功能描述:監控電路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。