- 您現在的位置：買賣IC網 > PDF目錄11653 > MAX7360ETL+T (Maxim Integrated Products)IC CTRLR KEY-SW I2C 40TQFN-EP PDF資料下載
參數資料
| 型號： | MAX7360ETL+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTRLR KEY-SW I2C 40TQFN-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 控制器 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | I²C，2 線串口 |
| 電流 - 電源： | 50µA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-TQFN-EP（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
16
Maxim Integrated
I2C-Interfaced Key-Switch Controller and LED
Driver/GPIOs with Integrated ESD Protection
MAX7360
transaction, either read or write, if SCL low exceeds
20ms. After a bus timeout, the MAX7360 waits for a valid
START condition before responding to a consecutive
transmission. This feature can be enabled or disabled
under user control by writing to the configuration register
(Table 8 in the Register Tables section).
Message Format for Writing
the Key-Scan Controller
A write to the MAX7360 comprises the transmission of the
slave address with the R/W bit set to zero, followed by at
least 1 byte of information. The first byte of information
is the command byte. The command byte determines
which register of the MAX7360 is to be written by the next
byte, if received. If a STOP condition is detected after the
command byte is received, the MAX7360 takes no further
action (Figure 7) beyond storing the command byte.
Any bytes received after the command byte are data bytes.
The first data byte goes into the internal register of the
MAX7360 selected by the command byte (Figure 8).
If multiple data bytes are transmitted before a STOP condi-
tion is detected, these bytes are generally stored in subse-
quent MAX7360 internal registers, because the command
byte address generally autoincrements (Table 4).
Message Format for Reading
the Key-Scan Controller
The MAX7360 is read using the internally stored com-
mand byte as an address pointer, the same way the
stored command byte is used as an address pointer
for a write. The pointer generally autoincrements after
each data byte is read using the same rules as for a
write (Table 4). Thus, a read is initiated by first config-
uring the MAX7360’s command byte by performing a
write (Figure 7). The master can now read n consecutive
bytes from the MAX7360, with the first data byte being
read from the register addressed by the initialized com-
mand byte. When performing read-after-write verifica-
tion, remember to reset the command byte’s address,
because the stored command byte address is generally
autoincremented after the write (Figure 9, Table 4).
Operation with Multiple Masters
When the MAX7360 is operated on a 2-wire interface
with multiple masters, a master reading the MAX7360
uses a repeated start between the write that sets the
MAX7360’s address pointer, and the read(s) that takes
the data from the location(s). This is because it is pos-
sible for master 2 to take over the bus after master 1 has
set up the MAX7360’s address pointer, but before mas-
ter 1 has read the data. If master 2 subsequently resets
the MAX7360’s address pointer, master 1’s read can be
from an unexpected location.
Command Address Autoincrementing
Address autoincrementing allows the MAX7360 to be
configured with fewer transmissions by minimizing the
number of times the command address needs to be
sent. The command address stored in the MAX7360
generally increments after each data byte is written or
read (Table 4). Autoincrement only works when doing a
multiburst read or write.
Applications Information
Reset from I2C
After a catastrophic event such as ESD discharge or
microcontroller reset, use bit D7 of the configuration
register (0x01) as a software reset for the key-switch
state (the key-switch register values and FIFO remain
unaffected). Use bit D4 of the GPIO global configura-
tion register (0x40) as a software reset for the GPIOs.
Figure 9. N Data Bytes Received
Table 4. Autoincrement Rules
REGISTER
FUNCTION
ADDRESS
CODE (hex)
AUTOINCREMENT
ADDRESS (hex)
Keys FIFO
0x00
Autoshutdown
0x06
0x00
All other key switch
0x01 to 0x05
Addr + 0x01
All other GPIO
0x40 to 0x5F
Addr + 0x01
S
A
P
0
SLAVE ADDRESS
COMMAND BYTE
DATA BYTE
N BYTES
AUTOINCREMENT
COMMAND BYTE ADDRESS
D7
D6
D5
D4
D3
D2
D1
D0
D1
D0
D3
D2
D5
D4
D7
D6
ACKNOWLEDGE FROM MAX7360
R/W
相關PDF資料 |
PDF描述 |
|---|---|
| MXB7846EEE+T | IC CNTRLR TOUCH RES 16QSOP |
| V24C28M100BG | CONVERTER MOD DC/DC 28V 100W |
| PCF51JM128VLH | MCU 32BIT 128K FLASH 64-LQFP |
| V24C28M100B | CONVERTER MOD DC/DC 28V 100W |
| MC9S08LC36LH | IC MCU 36K FLASH 2K RAM 64-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7360EVKIT+ | 制造商:Maxim Integrated Products 功能描述:I2C-INTERFACED KEY-SWITCH CONTROLLE - Boxed Product (Development Kits) |
| MAX7360EWX+ | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:I2C-Interfaced Key-Switch Controller and LED Driver/GPIOs with Integrated ESD Protection |
| MAX7360EWX+T | 功能描述:外圍驅動器與原件 - PCI Key-Switch Ctlr & LED Driver/GPIO RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| MAX7365EWA70+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX7365EWA70+T | 制造商:Maxim Integrated Products 功能描述:KEYBOARD CONTROLLER PLUS 5 ADDITIONAL GPIOS - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CTRLR KEY-SWITCH I2C 25WLP |
發布緊急采購，3分鐘左右您將得到回復。