參數資料
型號: MAX7456EUI+
廠商: Maxim Integrated Products
文件頁數: 35/44頁
文件大?。?/td> 0K
描述: IC ON-SCREEN DISPLAY 28-TSSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 50
類型: OSD(屏幕顯示)視頻發生器
應用: 安全系統,視頻路由
安裝類型: 表面貼裝
封裝/外殼: 28-SOIC(0.173",4.40mm 寬)裸露焊盤
供應商設備封裝: 28-TSSOP 裸露焊盤
包裝: 管件
產品目錄頁面: 1424 (CN2011-ZH PDF)
4) Write DMM[5:3] = XXX to set the Local Background
Control (LBC), Blink (BLK) and Invert (INV) attribute
bits that will be applied to all characters.
5) Write CA data in the intended character order to dis-
play text on the screen. It will be stored along with a
Character Attribute byte derived from DMM[5:3].
See Figure 19. This is the single byte operation. The
DMDI[7:0] address is automatically set by auto-
increment mode. The display memory address is
automatically incremented following the write opera-
tion until the final display memory address is
reached.
6) Write CA = FFh to terminate the auto-increment
mode.
Note: The character stored at CA[7:0] = FFh is not avail-
able for use in auto-increment mode. Read operation is
not possible before auto-increment mode is terminated.
Steps for Reading from Display
Memory in 8-Bit Mode
1) Write DMM[6] = 1 to select the 8-bit operation mode.
2) Write DMAH[1] = 0 to read the Character Address
byte or DMAH[1] = 1 to read the Character Attribute
byte.
3) Write to DMAH[0] to select the MSB of the address
where data must be read from (Figure 10).
4) Write to DMAL[7:0] to select all the lower order bits,
except for the MSB, of the address where data must
be read from (Figure 10).
5) Read DMDO[7:0] to read the data from the selected
location in the display memory (Figure 10).
Steps for Reading from Display
Memory in 16-Bit Mode
1) Write DMM[6] = 0 to select the 16-bit operation
mode.
2) Write DMAH[0] = x to select the MSB and
DMAL[7:0] = xxH to select the lower order bits of
the address where the character data is to be read.
This address determines the location of the charac-
ter on the display (see Figure 10).
3) Read DMDO[15:0] to read the Character Address
byte and the Character Attribute byte from the
selected location in the display memory. The first
data byte is the Character Address (CA[7:0]), and
the second byte contains the Character Attribute
bits (Figure 20). Note that the bit positions of the
Character Attribute byte when read, differ from
when they are written. See the
Display Memory Data
Out Register (DMDO) section and Figure 20 for a
description of the bit locations of the attribute bits
when reading.
Note: If an internal display-memory read request
occurs simultaneously with an SPI display-memory
operation, the internal read request is ignored, and the
display of that character, during that field time, may
appear to momentarily break up. See the
Synchronous
OSD Updates section.
Synchronous OSD Updates
The display of a character may momentarily appear to
break up if an internal display-memory read request
occurs simultaneously with an SPI display-memory
operation. Momentary breakup of the OSD image can
be prevented by writing to the display memory during
the vertical blanking interval. This can be achieved by
using VSYNC as an interrupt to the host processor to
initiate writing to the display memory. Alternatively, the
OSD image can be synchronously disabled before writ-
ing to the display memory and synchronously re-
enabled afterwards (see VM0[3:2]).
Single-Channel Monochrome On-Screen
Display with Integrated EEPROM
Table 5. Display-Memory Access Modes and SPI Operations
OPERATING
MODE
AUTO-INCREMENT
MODE DISABLED
DMM[0] = 0
No. OF READ
OPERATIONS
No. OF WRITE
OPERATIONS
AUTO-INCREMENT
MODE ENABLED
DMM[0] = 1
No. OF WRITE
OPERATIONS
One-time setup
2
1
One-time setup
6
16-Bit Mode
DMM[6] = 0
Per character
3
Per character
1
One-time setup
1
One-time setup
6
8-Bit Mode
DMM[6] = 1
Per character
6
Per character
1
MAX7456
40
Maxim Integrated
相關PDF資料
PDF描述
MAX242EPN+ IC TXRX RS232 5V 18-DIP
MAX3815CCM+D IC EQUALIZER VIDEO 48-TQFP
MAX9135GHJ+ IC SW LVDS CROSSBAR 32TQFP-EP
MAX242EWN+ IC TXRX RS232 5V 18-SOIC
MAX9134GHJ+ IC SW LVDS CROSSBAR 32TQFP-EP
相關代理商/技術參數
參數描述
MAX7456EUI/GH9 制造商:Maxim Integrated Products 功能描述:SINGLE-CHANNEL MONOCHROME ON-SCREEN DISPLAY - Rail/Tube
MAX7456EUI+ 功能描述:視頻 IC Monochrome On Scrn Display Generator RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
MAX7456EUI+T 功能描述:視頻 IC Monochrome On Scrn Display Generator RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
MAX7456EUI+W 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX7456EVKIT 功能描述:顯示開發工具 RoHS:否 制造商:4D Systems 產品:4Display Shields 工具用于評估:?OLED-160-G1, ?OLED-160-G2 接口類型:Serial 工作電源電壓:5 V